Vim3 not booting

rider · February 19, 2020, 11:23am

Hi all,

I installed Ubuntu latest image on emmc using windows pc,witch finished successfully. and it seems there is some issue with emmc from my understanding of linux boot logs.
moreover i tried to clone image from another vim3 we have using krescue, but result are the same.

bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02

L0:00000000
L1:20000703
L2:00008067
L3:14000000
B2:00402000
B1:e0f83180

TE: 194018

BL2 Built : 15:22:05, Aug 28 2019. g12b g1bf2b53 - luan.yuan@droid15-sz

Board ID = 8
Set A53 clk to 24M
Set A73 clk to 24M
Set clk81 to 24M
A53 clk: 1200 MHz
A73 clk: 1200 MHz
CLK81: 166.6M
smccc: 00033dbf
eMMC boot @ 0
sw8 s
DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 15:22:01
board id: 8
Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part                                                                                                                                                             : 0
fw parse done
Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part:                                                                                                                                                              0
Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part:                                                                                                                                                              0
PIEI prepare done
fastboot data load
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000                                                                                                                                                             , part: 0
00000000
emmc switch 0 ok
fastboot data verify
verify result: 265
Cfg max: 4, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe
ddr clk to 1608MHz
Load ddrfw from eMMC, src: 0x0003c200, des: 0xfffd0000, size: 0x0000c000, part:                                                                                                                                                              0

dmc_version 0001
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of Write leveling coarse delay
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Load ddrfw from eMMC, src: 0x00048200, des: 0xfffd0000, size: 0x0000c000, part:                                                                                                                                                              0
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!

channel==0
RxClkDly_Margin_A0==67 ps 7
TxDqDly_Margin_A0==106 ps 11
RxClkDly_Margin_A1==67 ps 7
TxDqDly_Margin_A1==106 ps 11
TrainedVREFDQ_A0==27
TrainedVREFDQ_A1==26
VrefDac_Margin_A0==28
DeviceVref_Margin_A0==26
VrefDac_Margin_A1==29
DeviceVref_Margin_A1==26


channel==1
RxClkDly_Margin_A0==87 ps 9
TxDqDly_Margin_A0==106 ps 11
RxClkDly_Margin_A1==106 ps 11
TxDqDly_Margin_A1==106 ps 11
TrainedVREFDQ_A0==25
TrainedVREFDQ_A1==24
VrefDac_Margin_A0==26
DeviceVref_Margin_A0==25
VrefDac_Margin_A1==27
DeviceVref_Margin_A1==24

 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004

soc_vref_reg_value 0x 00000027 00000029 00000028 00000028 00000027 00000029 0000                                                                                                                                                             0026 00000026 00000026 00000027 00000026 00000025 00000027 00000026 00000028 000                                                                                                                                                             00027 00000027 00000028 00000028 0000002a 00000027 00000025 00000027 00000028 00                                                                                                                                                             000028 00000029 00000028 00000028 00000027 00000028 00000028 00000027 dram_vref_                                                                                                                                                             reg_value 0x 00000013
2D training succeed
aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 13:54:19
auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 2048MB
DMC_DDR_CTRL: 00e00024DDR size: 3928MB
cs0 DataBus test pass
cs1 DataBus test pass
cs0 AddrBus test pass
cs1 AddrBus test pass

100bdlr_step_size ps== 471
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part                                                                                                                                                             : 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d0000, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
MVN_1=0x00000000
MVN_2=0x00000000
[Image: g12b_v1.1.3390-6ac5299 2019-09-26 14:10:05 luan.yuan@droid15-sz]
OPS=0x10
ring efuse init
chipver efuse init
29 0b 10 00 01 1a 1d 00 00 0e 35 37 4d 4d 4e 50
[0.018961 Inits done]
secure task start!
high task start!
low task start!
run into bl31
NOTICE:  BL31: v1.3(release):4fc40b1
NOTICE:  BL31: Built : 15:58:17, May 22 2019
NOTICE:  BL31: G12A normal boot!
NOTICE:  BL31: BL33 decompress pass
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01 (Dec 31 2019 - 00:36:50)

DRAM:  3.8 GiB
Relocation Offset is: d6e46000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 00000000d7f39548
aml_i2c_init_port init regs for 0
MMC:   aml_priv->desc_buf = 0x00000000d3e36a70
aml_priv->desc_buf = 0x00000000d3e38db0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x1, tx-dly 0, clock 40000000
aml_sd_retry_refix[983]:delay = 0x0,gadjust =0x12000
[mmc_startup] mmc refix success
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
start dts,buffer=00000000d3e3b620,dt_addr=00000000d3e3b620
get_partition_from_dts() 91: ret 0
parts: 3
00:      logo   0000000000800000 1
01:   ramdisk   0000000002000000 1
02:    rootfs   ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x6c00000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3477: calc de0f5855, store de0f5855
_verify_dtb_checksum()-3477: calc de0f5855, store de0f5855
dtb_read()-3694: total valid 2
update_old_dtb()-3675: do nothing
aml_i2c_init_port init regs for 0
fusb302_init: Device ID: 0x91
CC connected in 1 as UFP
fusb302 detect chip.port_num = 0

amlkey_init() enter!
[EFUSE_MSG]keynum is 1
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
cvbs: cpuid:0x29
LCD_RESET PIN: 0
lcd: detect mode: tablet, key_valid: 0
lcd: detect lcd_clk_path: 1
lcd: failed to get lcd_cpu_gpio_names
lcd: load config from dts
lcd: pinctrl_version: 2
lcd: use panel_type=lcd_0
lcd: bl: pinctrl_version: 2
lcd: bl: name: backlight_pwm, method: 1
lcd: bl: aml_bl_power_ctrl: 0
Net:   __phy_realtek_initPhy 0 not found
dwmac.ff3f0000
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 1
MACADDR:02:00:00:1d:1a:01(from chipid)

upgrade_step=2
reboot_mode:::: cold_boot

amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 1
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet

mac address: c8:63:14:70:50:cc
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
edid preferred_mode is <NULL>[0]
hdr mode is 0
dv  mode is ver:0  len: 0
hdr10+ mode is 0
HDMI cable is NOT connected
hpd_state=0
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
card out
** Bad device mmc 0 **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
750054 bytes read in 36 ms (19.9 MiB/s)
[OSD]osd_hw.free_dst_data: 0,1079,0,1919
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[panel] is invalid
hdmitx: outputmode[panel] is invalid
vpp: vpp_matrix_update: 0
vpp: g12a/b post2(bit12) matrix: YUV limit -> RGB ..............
lcd: enable: TS050, mipi, 1080x1920@47.6Hz
lcd: tablet driver init(ver 20180718): mipi
lcd: lcd_pll_wait_lock: pll_lock=1, wait_loop=1
vpp: vpp_init_lcd_gamma_table
lcd: pixel_clk = 120.000MHz, bit_rate = 960.000MHz, lanebyteclk = 120.000MHz
lcd:  Waiting STOP STATE LANE
lcd: dsi init on
lcd: bl: set level: 100, last level: 0
lcd: bl: aml_bl_power_ctrl: 1
lcd: clear mute
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0

amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 1
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet

mac address: c8:63:14:70:50:cc
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
gpio: pin GPIOAO_7 (gpio 7) value is 1
saradc: 0x28a, hw_ver: 0x32 (VIM3.V12)
Product checking: pass! Hardware version: VIM3.V12
reboot_mode=cold_boot
normal power on
boot wol: disable
port mode is usb3.0
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
pll tsensor avg: 0x2013, u_efuse: 0x80a8
temp1: 37
ddr tsensor avg: 0x200c, u_efuse: 0x801b
temp2: 39
device cool done
cfgload: start ...
cfgload: reading /boot.ini from mmc 0:1 ...
card out
** Bad device mmc 0 **
cfgload: no /boot.ini or empty file on mmc 0:1
cfgload: reading /boot/boot.ini from mmc 0:1 ...
card out
** Bad device mmc 0 **
cfgload: no /boot/boot.ini or empty file on mmc 0:1
cfgload: reading /boot.ini from mmc 1:1 ...
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
cfgload: no /boot.ini or empty file on mmc 1:1
cfgload: reading /boot/boot.ini from mmc 1:1 ...
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
cfgload: no /boot/boot.ini or empty file on mmc 1:1
cfgload: reading /boot/boot.ini from mmc 1:5 ...
8183 bytes read in 4 ms (2 MiB/s)
cfgload: applying boot.ini...
[#] Script a:d3e3e140 l:8163 c:0 s:0 - run
Starting boot.ini...
saradc: 0x28a, hw_ver: 0x32 (VIM3.V12)
uboot type: vendor
Scanning mmc 0:1...
card out
** Bad device mmc 0 **
Scanning mmc 0:5...
card out
** Bad device mmc 0 **
Scanning mmc 1:1...
** Unrecognized filesystem type **
Scanning mmc 1:5...
8760290 bytes read in 251 ms (33.3 MiB/s)
28979712 bytes read in 814 ms (34 MiB/s)
87858 bytes read in 8 ms (10.5 MiB/s)
2672 bytes read in 5 ms (521.5 KiB/s)
Import env.txt
Can not get u-boot part UUID, set to NULL
Booting legacy kernel...
port mode is usb3.0
HDMI: Autodetect: 1080p60hz
## Loading init Ramdisk from Legacy Image at 13000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    8760226 Bytes = 8.4 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
load dtb from 0x1000000 ......
## Flattened Device Tree blob at 01000000
   Booting using the fdt blob at 0x1000000
   reserving fdt memory region: addr=1000000 size=16000
   Loading Ramdisk to 7efa5000, end 7f7ffba2 ... OK
   Loading Device Tree to 000000001ffe7000, end 000000001fffffff ... OK

Starting kernel ...

uboot time: 5273626 us

rider · February 19, 2020, 11:25am

boot log continue:

[    0.000000@0] Booting Linux on physical CPU 0x0
[    0.000000@0] Linux version 4.9.206 (khadas@3a97a4844f91) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #13 SMP PREEMPT Tue Dec 31 00:37:47 CST 2019
[    0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[    0.000000@0] Machine model: Khadas VIM3
[    0.000000@0] efi: Getting EFI parameters from FDT:
[    0.000000@0] efi: UEFI not found.
[    0.000000@0] OF: reserved mem: __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[    0.000000@0] Reserved memory: created CMA memory pool at 0x0000000005000000, size 4 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,secmon, compatible id shared-dma-pool
[    0.000000@0] OF: reserved mem: __reserved_mem_alloc_size, start:0x000000007f800000, end:0x0000000080000000, len:8 MiB
[    0.000000@0] Reserved memory: created CMA memory pool at 0x000000007f800000, size 8 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,meson-fb, compatible id shared-dma-pool
[    0.000000@0] Reserved memory: created CMA memory pool at 0x00000000e5800000, size 128 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,ion-dev, compatible id shared-dma-pool
[    0.000000@0] Reserved memory: created CMA memory pool at 0x00000000e3000000, size 40 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,di_cma, compatible id shared-dma-pool
[    0.000000@0] Reserved memory: created DMA memory pool at 0x00000000e3000000, size 0 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,ppmgr, compatible id shared-dma-pool
[    0.000000@0] Reserved memory: created CMA memory pool at 0x00000000cfc00000, size 308 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,codec_mm_cma, compatible id shared-dma-pool
[    0.000000@0] OF: reserved mem: initialized node linux,codec_mm_reserved, compatible id amlogic, codec-mm-reserved
[    0.000000@0] Reserved memory: created CMA memory pool at 0x00000000cbc00000, size 64 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,vdin0_cma, compatible id shared-dma-pool
[    0.000000@0] Reserved memory: created CMA memory pool at 0x00000000c7c00000, size 64 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,vdin1_cma, compatible id shared-dma-pool
[    0.000000@0] Reserved memory: created CMA memory pool at 0x00000000c6c00000, size 16 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,galcore, compatible id shared-dma-pool
[    0.000000@0] Reserved memory: created CMA memory pool at 0x00000000a7c00000, size 496 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,isp_cma, compatible id shared-dma-pool
[    0.000000@0] Reserved memory: created CMA memory pool at 0x00000000a4c00000, size 48 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,adapt_cma, compatible id shared-dma-pool
[    0.000000@0] Reserved memory: created CMA memory pool at 0x00000000a0c00000, size 64 MiB
[    0.000000@0] OF: reserved mem: initialized node linux,gdc_cma, compatible id shared-dma-pool
[    0.000000@0] cma: Reserved 8 MiB at 0x00000000a0400000
[    0.000000@0] psci: probing for conduit method from DT.
[    0.000000@0] psci: PSCIv1.0 detected in firmware.
[    0.000000@0] psci: Using standard PSCI v0.2 function IDs
[    0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000@0] psci: SMC Calling Convention v1.1
[    0.000000@0] percpu: Embedded 25 pages/cpu s64920 r8192 d29288 u102400
[    0.000000@0] Detected VIPT I-cache on CPU0
[    0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[    0.000000@0] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 957600
[    0.000000@0] Kernel command line: root=LABEL=ROOTFS rootfstype=ext4 rootflags=data=writeback rw ubootpart=NULL console=ttyS0,115200n8 console=tty0 no_console_suspend consoleblank=0 logo=osd0,loaded,0x3d800000,panel vout=panel,enable hdmimode=1080p60hz  fsck.repair=yes net.ifnames=0 ddr_size= wol_enable=0 jtag=disable mac=c8:63:14:70:50:cc androidboot.mac=c8:63:14:70:50:cc  fan=auto khadas_board=VIM3 hwver=VIM3.V12 coherent_pool=2M reboot_mode=cold_boot imagetype=EMMC uboottype=vendor
[    0.000000@0] fb: osd0
[    0.000000@0] fb: loaded
[    0.000000@0] fb: 0x3d800000
[    0.000000@0] fb: panel
[    0.000000@0] vout: panel
[    0.000000@0] vout: enable: 1
[    0.000000@0] vout: get hdmimode: 1080p60hz
[    0.000000@0] init_wol_state, wol_enable=0
[    0.000000@0] jtag: jtag select disable
[    0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000@0] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000@0] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000@0] Memory: 2504988K/3891200K available (14908K kernel code, 1868K rwdata, 5968K rodata, 5504K init, 1500K bss, 108260K reserved, 1277952K cma-reserved)
[    0.000000@0] Virtual kernel memory layout:
[    0.000000@0]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000@0]     vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000   (   250 GB)
[    0.000000@0]       .text : 0xffffff8009080000 - 0xffffff8009f10000   ( 14912 KB)
[    0.000000@0]     .rodata : 0xffffff8009f10000 - 0xffffff800a4f0000   (  6016 KB)
[    0.000000@0]       .init : 0xffffff800a4f0000 - 0xffffff800aa50000   (  5504 KB)
[    0.000000@0]       .data : 0xffffff800aa50000 - 0xffffff800ac23200   (  1869 KB)
[    0.000000@0]        .bss : 0xffffff800ac23200 - 0xffffff800ad9a224   (  1501 KB)
[    0.000000@0]     fixed   : 0xffffffbefe7fd000 - 0xffffffbefec00000   (  4108 KB)
[    0.000000@0]     PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000   (    16 MB)
[    0.000000@0]     vmemmap : 0xffffffbf00000000 - 0xffffffc000000000   (     4 GB maximum)
[    0.000000@0]               0xffffffbf00000000 - 0xffffffbf03b60000   (    59 MB actual)
[    0.000000@0]     memory  : 0xffffffc000000000 - 0xffffffc0ed800000   (  3800 MB)
[    0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[    0.000000@0] Preemptible hierarchical RCU implementation.
[    0.000000@0]        Build-time adjustment of leaf fanout to 64.
[    0.000000@0]        RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[    0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
[    0.000000@0] NR_IRQS:64 nr_irqs:64 0
[    0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[    0.000000@0] g12a_aoclkc_init: register ao clk ok!
[    0.000000@0] Meson chip version = RevB (29:B - 10:0)
[    0.000000@0] meson_g12a_sdemmc_init: register amlogic sdemmc clk
[    0.000000@0] meson_g12a_sdemmc_init: register amlogic sdemmc clk
[    0.000000@0] meson_g12a_gpu_init: register meson gpu clk
[    0.000000@0] meson_g12a_media_init: register meson media clk
[    0.000000@0] meson_g12a_misc_init: register amlogic g12a misc clks
[    0.000000@0] meson_g12a_misc_init: done.
[    0.000000@0] g12a_clkc_init initialization complete
[    0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000043@0] meson_bc_timer: mclk->mux_reg =ffffff800800c190,mclk->reg =ffffff800800e194
[    0.000687@0] Console: colour dummy device 80x25
[    0.002247@0] console [tty0] enabled
[    0.002272@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.002304@0] pid_max: default: 32768 minimum: 301
[    0.002351@0] thread_stack_cache_init, vmap:ffffffc09b87a780, bitmap:ffffffc09b874000, cache page:9b880
[    0.002382@0] thread_stack_cache_init, allocation vm area:ffffffc09b83b780, addr:ffffff8020000000, size:20001000
[    0.002410@0] cpu 0, vmap_stack:[ffffffc0a02feae0-ffffffc0a0302ad0]
[    0.002428@0] cpu 0, irq_stack: [ffffffc0a02f5060-ffffffc0a02f9050]
[    0.002445@0] cpu 1, vmap_stack:[ffffffc0a0317ae0-ffffffc0a031bad0]
[    0.002462@0] cpu 1, irq_stack: [ffffffc0a030e060-ffffffc0a0312050]
[    0.002479@0] cpu 2, vmap_stack:[ffffffc0a0330ae0-ffffffc0a0334ad0]
[    0.002496@0] cpu 2, irq_stack: [ffffffc0a0327060-ffffffc0a032b050]
[    0.002514@0] cpu 3, vmap_stack:[ffffffc0a0349ae0-ffffffc0a034dad0]
[    0.002531@0] cpu 3, irq_stack: [ffffffc0a0340060-ffffffc0a0344050]
[    0.002548@0] cpu 4, vmap_stack:[ffffffc0a0362ae0-ffffffc0a0366ad0]
[    0.002565@0] cpu 4, irq_stack: [ffffffc0a0359060-ffffffc0a035d050]
[    0.002582@0] cpu 5, vmap_stack:[ffffffc0a037bae0-ffffffc0a037fad0]
[    0.002599@0] cpu 5, irq_stack: [ffffffc0a0372060-ffffffc0a0376050]
[    0.002676@0] Security Framework initialized
[    0.002695@0] SELinux:  Initializing.
[    0.002777@0] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.002799@0] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.003478@0] ftrace: allocating 48359 entries in 189 pages
[    0.091634@0] sched-energy: Sched-energy-costs installed from DT
[    0.091667@0] CPU0: update cpu_capacity 631
[    0.091692@0] ASID allocator initialised with 65536 entries
[    0.151484@0] secmon: clear_range:5100000 200000
[    0.152293@0] EFI services will not be available.
[    0.199838@1] Detected VIPT I-cache on CPU1
[    0.199892@1] CPU1: update cpu_capacity 631
[    0.199894@1] CPU1: Booted secondary processor [410fd034]
[    0.232381@2] Detected VIPT I-cache on CPU2
[    0.232424@2] CPU2: update cpu_capacity 1192
[    0.232427@2] CPU2: Booted secondary processor [410fd092]
[    0.263940@3] Detected VIPT I-cache on CPU3
[    0.263963@3] CPU3: update cpu_capacity 1192
[    0.263965@3] CPU3: Booted secondary processor [410fd092]
[    0.296030@4] Detected VIPT I-cache on CPU4
[    0.296052@4] CPU4: update cpu_capacity 1192
[    0.296055@4] CPU4: Booted secondary processor [410fd092]
[    0.328110@5] Detected VIPT I-cache on CPU5
[    0.328132@5] CPU5: update cpu_capacity 1192
[    0.328135@5] CPU5: Booted secondary processor [410fd092]
[    0.328229@0] Brought up 6 CPUs
[    0.328444@0] SMP: Total of 6 processors activated.
[    0.328466@0] CPU features: detected feature: 32-bit EL0 Support
[    0.328612@0] CPU: All CPU(s) started at EL2
[    0.328666@0] alternatives: patching kernel code
[    0.330654@0] addr:ffffff80200c3e16 is in kernel, size fix 4096->10, data:mode=0755
[    0.330852@2] devtmpfs: initialized
[    0.345126@1] DMI not present or invalid.
[    0.345531@1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.345578@1] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.345829@1] pinctrl core: initialized pinctrl subsystem
[    0.346904@1] NET: Registered protocol family 16
[    0.348867@1] schedtune: init normalization constants...
[    0.348901@1] schedtune: CLUSTER[0-1]      min_pwr:     0 max_pwr:    42
[    0.348923@1] schedtune: CPU[0]            min_pwr:     0 max_pwr:   279
[    0.348943@1] schedtune: CPU[1]            min_pwr:     0 max_pwr:   279
[    0.348964@1] schedtune: CLUSTER[2-5]      min_pwr:     0 max_pwr:   110
[    0.348985@1] schedtune: CPU[2]            min_pwr:     0 max_pwr:  1048
[    0.349005@1] schedtune: CPU[3]            min_pwr:     0 max_pwr:  1048
[    0.349025@1] schedtune: CPU[4]            min_pwr:     0 max_pwr:  1048
[    0.349046@1] schedtune: CPU[5]            min_pwr:     0 max_pwr:  1048
[    0.349066@1] schedtune: SYSTEM            min_pwr:     0 max_pwr:  4902
[    0.349087@1] schedtune: using normalization constants mul: 2882587190 sh1: 1 sh2: 12
[    0.349112@1] schedtune: verify normalization constants...
[    0.349131@1] schedtune: max_pwr/2^0: 4902 => norm_pwr:  1024
[    0.349150@1] schedtune: max_pwr/2^1: 2451 => norm_pwr:   512
[    0.349168@1] schedtune: max_pwr/2^2: 1225 => norm_pwr:   255
[    0.349187@1] schedtune: max_pwr/2^3:  612 => norm_pwr:   127
[    0.349206@1] schedtune: max_pwr/2^4:  306 => norm_pwr:    63
[    0.349225@1] schedtune: max_pwr/2^5:  153 => norm_pwr:    31
[    0.349244@1] schedtune: configured to support 5 boost groups
[    0.364114@2] cpuidle: using governor menu
[    0.364238@2] register canvas platform driver
[    0.364275@2] register rdma platform driver
[    0.364309@2] aml_vdac_init: module init
[    0.365614@2] vdso: 2 pages (1 code @ ffffff8009f17000, 1 data @ ffffff800aa55000)
[    0.365644@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.367145@2] DMA: preallocated 2048 KiB pool for atomic allocations
[    0.367309@2] clkmsr: clkmsr: driver init
[    0.367324@2] codec_mm_module_init
[    0.367357@2] media_configs_system_init
[    0.367863@2] pstore: using zlib compression
[    0.368534@2] console [pstore-1] enabled
[    0.368614@2] pstore: Registered ramoops as persistent store backend
[    0.368634@2] ramoops: attached 0x100000@0x7400000, ecc: 0/0
[    0.368651@2] ramoops: ramoops_io_en:0 1 old:0x0 ftrace_size:0x40000
[    0.370355@2] aml_iomap: amlogic iomap probe done
[    0.370803@2] vpu: driver version: v20190314(8-g12b)
[    0.370824@2] vpu: load vpu_clk: 666666667Hz(7)
[    0.371028@2] vpu: clktree_init
[    0.371082@2] vpu: vpu_probe OK
[    0.374846@2] clkmsr: msr_clk_reg0=ffffff800836d004,msr_clk_reg2=ffffff800837c00c
[    0.374877@2] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[    0.379759@2] aml_vdac_probe:probe start.cpu_id:6,name:meson-g12ab-vdac
[    0.379941@2] aml_vdac_probe: ok
[    0.380080@2] canvas_probe reg=00000000ff638000,size=2000
[    0.380104@2] canvas maped reg_base =ffffff8008452000
[    0.385518@2] rdma_probe,cpu_type:0, ver:0, len:8
[    0.385753@2] rdma_register, rdma_table_addr ffffff8008475000 rdma_table_addr_phy a0600000 reg_buf ffffffc09b210000
[    0.385781@2] rdma_register success, handle 1 table_size 32768
[    0.385799@2] set_rdma_handle video rdma handle = 1.
[    0.385814@2] g12b revb!!!!
[    0.385869@2] rdma_register, rdma_table_addr ffffff8008491000 rdma_table_addr_phy a0608000 reg_buf ffffffc09b240000
[    0.385895@2] rdma_register success, handle 2 table_size 32768
[    0.385911@2] set_rdma_handle video rdma handle = 2.
[    0.386897@2] aml_snd_reg_map[0], reg:ff640000, size:2000
[    0.386926@2] aml_snd_reg_map[1], reg:ff642000, size:2000
[    0.386952@2] aml_snd_reg_map[2], reg:ff64a000, size:2000
[    0.386977@2] aml_snd_reg_map[3], reg:ff656000, size:1800
[    0.387003@2] aml_snd_reg_map[4], reg:ffd01000, size:1000
[    0.387020@2] amlogic auge_snd_iomap probe done
[    0.389272@2] cvbs_out: cvbsout_probe, cpu_id:5,name:meson-g12b-cvbsout
[    0.389302@2] cvbs_out: clk_path config null
[    0.389319@2] cvbs_out: error: failed to get vdac_config
[    0.389467@2] vout: vout1: register server: cvbs_vout_server
[    0.389484@2] cvbs_out: register cvbs module server ok
[    0.389501@2] vout: vout2: register server: cvbs_vout2_server
[    0.389517@2] cvbs_out: register cvbs module vout2 server ok
[    0.389535@2] cvbs_out: chrdev devno 264241152 for disp
[    0.389731@2] cvbs_out: create cdev cvbs
[    0.389748@2] cvbs_out: cvbsout_probe OK
[    0.390378@2] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma
[    0.390464@2] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma
[    0.390487@2] codec_mm_probe ok
[    0.545311@2] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.545945@2] vgaarb: loaded
[    0.546193@2] SCSI subsystem initialized
[    0.546402@2] usbcore: registered new interface driver usbfs
[    0.546462@2] usbcore: registered new interface driver hub
[    0.546547@2] usbcore: registered new device driver usb
[    0.546648@2] Linux video capture interface: v2.00
[    0.546737@2] pps_core: LinuxPPS API ver. 1 registered
[    0.546754@2] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.546792@2] PTP clock support registered
[    0.547072@2] dmi: Firmware registration failed.
[    0.547333@2] secmon: reserve_mem_size:0x300000
[    0.547424@2] secmon secmon: assigned reserved memory node linux,secmon
[    0.547843@2] secmon: get page:ffffffbf00140000, 5000
[    0.547863@2] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[    0.547887@2] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[    0.550068@2] hdmitx: system: amhdmitx_probe start
[    0.550089@2] hdmitx: system: Ver: 20190624
[    0.550124@2] hdmitx: system: hdmitx_device.chip_type : 11
[    0.550166@2] hdmitx: system: not find match pwr-ctl
[    0.550210@2] hdmitx: system: not find drm_amhdmitx
[    0.550241@2] hdmitx: system: hpd irq = 35
[    0.550354@2] hdmitx: system: hdcp22_tx_skp failed to probe
[    0.550373@2] hdmitx: system: hdcp22_tx_esm failed to probe
[    0.550763@2] vout: vout1: register server: hdmitx_vout_server
[    0.550784@2] vout: vout2: register server: hdmitx_vout2_server
[    0.551273@2] hdmitx: hdmitx20: Mapped PHY: 0xffd00000
[    0.551300@2] hdmitx: hdmitx20: Mapped PHY: 0xff634400
[    0.551323@2] hdmitx: hdmitx20: Mapped PHY: 0xff900000
[    0.551352@2] hdmitx: hdmitx20: Mapped PHY: 0xff800000
[    0.551371@2] hdmitx: hdmitx20: Mapped PHY: 0xff63c000
[    0.551388@2] hdmitx: hdmitx20: Mapped PHY: 0xffd00000
[    0.551405@2] hdmitx: hdmitx20: Mapped PHY: 0xff608000
[    0.551422@2] hdmitx: hdmitx20: Mapped PHY: 0xff600000
[    0.551440@2] hdmitx: hdmitx20: Mapped PHY: 0xffe01000
[    0.551461@2] hdmitx: hw: hdmitx_get_format:0x0
[    0.551477@2] hdmitx: hw: P_HHI_HDMI_CLK_CNTL :0x100
[    0.551492@2] hdmitx: hw: P_HHI_HDMI_PLL_CNTL :0x20000000
[    0.551728@2] hdmitx: hw: avmute set to 1
[    0.551746@2] hdmitx: system: fmt_attr default
[    0.551821@2] hdmitx: system: amhdmitx_probe end
[    0.552309@2] lcd: driver version: 20181012(5-g12a)
[    0.552432@2] lcd: detect mode: tablet, fr_auto_policy: 0, key_valid: 0
[    0.552451@2] lcd: detect lcd_clk_path: 1
[    0.552686@2] lcd: lcd_clktree_probe
[    0.552703@2] lcd: status: 3
[    0.552719@2] vout: vout1: register server: lcd_vout_server
[    0.552736@2] vout: vout2: register server: lcd_vout2_server
[    0.552754@2] lcd: lcd_get_config from dts
[    0.552770@2] lcd: error: failed to get null
[    0.552787@2] lcd: , invalid, 0bit, 1080x1920
[    0.552805@2] lcd: error: Out of clock range, reset to default setting
[    0.552890@2] lcd: error: lcd_debug_info_if is null
[    0.553041@2] lcd: lcd_fops_create OK
[    0.553090@2] lcd: request lcd_vsync_irq successful
[    0.553132@2] lcd: request lcd_vsync2_irq successful
[    0.553148@2] lcd: lcd_probe ok
[    0.553431@2] vout: create vout attribute OK
[    0.553542@2] vout: vout_fops_create OK
[    0.553559@2] vout: vout1: register server: nulldisp_vout_server
[    0.553648@2] vout: tvout monitor interval:500(ms), timeout cnt:20
[    0.553680@2] hdmitx: hdmitx_set_current_vmode[3724]
[    0.553697@2] hdmitx: system: recalc before 1080p60hz 60 1
[    0.553715@2] hdmitx: system: recalc after 1080p60hz 2997 50
[    0.553732@2] hdmitx: alread display in uboot
[    0.553747@2] vout: init mode 1080p60hz set ok
[    0.553763@2] vout: aml_tvout_mode_monitor
[    0.553784@2] vout: aml_vout_probe OK
[    0.554406@2] chip type:0x29
[    0.554693@2] Advanced Linux Sound Architecture Driver Initialized.
[    0.555143@2] Bluetooth: Core ver 2.22
[    0.555194@2] NET: Registered protocol family 31
[    0.555211@2] Bluetooth: HCI device and connection manager initialized
[    0.555233@2] Bluetooth: HCI socket layer initialized
[    0.555253@2] Bluetooth: L2CAP socket layer initialized
[    0.555293@2] Bluetooth: SCO socket layer initialized
[    0.555684@2] NetLabel: Initializing
[    0.555702@2] NetLabel:  domain hash size = 128
[    0.555718@2] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.555769@2] NetLabel:  unlabeled traffic allowed by default
[    0.557262@2] clocksource: Switched to clocksource arch_sys_counter
[    0.608814@2] VFS: Disk quotas dquot_6.6.0
[    0.608890@2] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.609026@2] FS-Cache: Loaded
[    0.616922@2] dtv_dmd:[amldtvdemod..]aml_dtvdemod_init.
[    0.616950@2] jtag: module init
[    0.617209@2] NET: Registered protocol family 2
[    0.617666@2] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.617862@2] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.618063@2] TCP: Hash tables configured (established 32768 bind 32768)
[    0.618130@2] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.618180@2] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.618351@2] NET: Registered protocol family 1
[    0.619915@2] wifi: power_on_pin_OD = 0;
[    0.619940@2] aml_wifi wifi: [wifi_dev_probe] no power_on_pin2
[    0.620039@2] aml_wifi wifi: [pwm_double_channel_conf_dt] wifi pwm dt ok
[    0.620066@2] aml_wifi wifi: [pwm_double_channel_conf] wifi pwm conf ok
[    0.620085@2] aml_wifi wifi: [wifi_dev_probe] dhd_static_buf setup
[    0.620102@2] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem 1.579.77.41.9
[    0.620348@2] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem prealloc ok
[    0.620368@2] aml_wifi wifi: [wifi_dev_probe] interrupt_pin=483
[    0.620386@2] aml_wifi wifi: [wifi_dev_probe] irq_num=0, irq_trigger_type=1
[    0.620405@2] aml_wifi wifi: [wifi_dev_probe] power_on_pin=482
[    0.620422@2] aml_wifi wifi: [wifi_dev_probe] clock_32k_pin=0
[    0.620595@2] aml_wifi wifi: [wifi_setup_dt] wifi_setup_dt
[    0.620674@2] aml_wifi wifi: [wifi_setup_dt] irq num is:(69)
[    0.620694@2] aml_wifi wifi: [wifi_setup_dt] interrupt_pin(483)
[    0.620721@2] aml_wifi wifi: [wifi_setup_dt] power_on_pin(482)
[    0.620969@2] Trying to unpack rootfs image as initramfs...
[    0.933661@2] Freeing initrd memory: 8552K
[    0.935656@2] hw perfevents: clusterb_enabled = 1
[    0.935678@2] hw perfevents: cpumasks 0x3, 0x3c
[    0.935717@2] hw perfevents: cluster A irq = 10
[    0.935764@2] hw perfevents: cluster B irq = 11
[    0.935841@2] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    0.937866@2] audit: initializing netlink subsys (disabled)
[    0.937934@2] audit: type=2000 audit(0.880:1): initialized
[    0.938528@2] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[    0.946568@2] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.946779@2] exFAT: Version 1.2.9
[    0.947471@2] Registering sdcardfs 0.1
[    0.947986@2] FS-Cache: Netfs 'cifs' registered for caching
[    0.948251@2] Key type cifs.spnego registered
[    0.948274@2] Key type cifs.idmap registered
[    0.948294@2] ntfs: driver 2.1.32 [Flags: R/O].
[    0.948516@2] jffs2: version 2.2. (NAND) (SUMMARY)  Â© 2001-2006 Red Hat, Inc.
[    0.948875@2] fuse init (API version 7.26)
[    0.952467@2] NET: Registered protocol family 38
[    0.952493@2] Key type asymmetric registered
[    0.952511@2] Asymmetric key parser 'x509' registered
[    0.952677@2] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[    0.952843@2] io scheduler noop registered (default)
[    0.952862@2] io scheduler deadline registered
[    0.952900@2] io scheduler cfq registered
[    0.960847@3] random: fast init done
[    0.960904@3] random: crng init done
[    0.961374@2] gpiomem-aml ff634000.gpiomem: Initialised: Registers at 0xff634000
[    0.961539@2] gpiomem-aml ff800000.gpiomem_ao: Initialised: Registers at 0xff800000
[    0.961662@2] [drm] Initialized
[    0.961809@2] Unable to detect cache hierarchy for CPU 0
[    0.969053@2] brd: module loaded
[    0.973418@2] loop: module loaded
[    0.973853@2] mcu_probe
[    0.973877@2] mcu_probe: board: 3, hwver: 2
[    0.974335@2] create_mcu_attrs
[    0.974427@2] mcu_probe,wol enable=0
[    0.975185@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[    0.976308@3] libphy: Fixed MDIO Bus: probed
[    0.976508@3] tun: Universal TUN/TAP device driver, 1.6
[    0.976526@3] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.977221@3]  REG0:Addr = ffffff80086fa540
[    0.977246@3]  ee eth reset:Addr = ffffff80086fc008
[    0.977303@3] read auto_cali_idx fail
[    0.977323@3] Not set  cali_val for REG1
[    0.977708@3] meson6-dwmac ff3f0000.ethernet: no reset control found
[    0.977729@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
[    0.977746@3]  Ring mode enabled
[    0.977761@3]  DMA HW capability register supported
[    0.977772@3]  Normal descriptors
[    0.977793@3]  RX Checksum Offload Engine supported
[    0.977809@3]        COE Type 2
[    0.977822@3]  TX Checksum insertion supported
[    0.977837@3]  Wake-Up On Lan supported
[    0.977882@3]  Enable RX Mitigation via HW Watchdog Timer
[    0.980527@3] libphy: stmmac: probed
[    0.980544@3] eth%d: No PHY found
[    0.998417@3] ethclk81 ff3f0000.ethernet: no reset control found
[    0.998440@3] stmmac - user ID: 0x11, Synopsys ID: 0x37
[    0.998457@3]  Ring mode enabled
[    0.998472@3]  DMA HW capability register supported
[    0.998483@3]  Normal descriptors
[    0.998503@3]  RX Checksum Offload Engine supported
[    0.998519@3]        COE Type 2
[    0.998533@3]  TX Checksum insertion supported
[    0.998547@3]  Wake-Up On Lan supported
[    0.998562@3]  Enable RX Mitigation via HW Watchdog Timer
[    1.001205@3] libphy: stmmac: probed
[    1.001222@3] eth%d: No PHY found
[    1.021508@3] PPP generic driver version 2.4.2
[    1.021697@3] PPP BSD Compression module registered
[    1.021716@3] PPP Deflate Compression module registered
[    1.021745@3] PPP MPPE Compression module registered
[    1.021763@3] NET: Registered protocol family 24
[    1.021849@3] usbcore: registered new interface driver asix
[    1.021933@3] usbcore: registered new interface driver ax88179_178a
[    1.021994@3] usbcore: registered new interface driver cdc_ether
[    1.022054@3] usbcore: registered new interface driver cdc_eem
[    1.022110@3] usbcore: registered new interface driver net1080
[    1.022181@3] usbcore: registered new interface driver rndis_host
[    1.022238@3] usbcore: registered new interface driver cdc_subset
[    1.022308@3] usbcore: registered new interface driver zaurus
[    1.022374@3] usbcore: registered new interface driver cdc_ncm
[    1.022442@3] usbcore: registered new interface driver qmi_wwan
[    1.022970@3] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.022989@3] ehci-pci: EHCI PCI platform driver
[    1.023046@3] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.023077@3] ohci-pci: OHCI PCI platform driver
[    1.023544@3] usbcore: registered new interface driver cdc_acm

rider · February 19, 2020, 11:25am

boot log continue:

[    1.023562@3] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.023631@3] usbcore: registered new interface driver cdc_wdm
[    1.023698@3] usbcore: registered new interface driver usb-storage
[    1.023803@3] usbcore: registered new interface driver usbserial
[    1.023855@3] usbcore: registered new interface driver usbserial_generic
[    1.023899@3] usbserial: USB Serial support registered for generic
[    1.023953@3] usbcore: registered new interface driver ch341
[    1.023994@3] usbserial: USB Serial support registered for ch341-uart
[    1.024046@3] usbcore: registered new interface driver cp210x
[    1.024088@3] usbserial: USB Serial support registered for cp210x
[    1.024139@3] usbcore: registered new interface driver ftdi_sio
[    1.024181@3] usbserial: USB Serial support registered for FTDI USB Serial Device
[    1.024242@3] usbcore: registered new interface driver option
[    1.024296@3] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.024352@3] usbcore: registered new interface driver pl2303
[    1.024393@3] usbserial: USB Serial support registered for pl2303
[    1.024829@3] mousedev: PS/2 mouse device common for all mice
[    1.025054@3] usbcore: registered new interface driver xpad
[    1.025119@3] edt_ft5x06 3-0038: probing for EDT FT5x06 I2C
[    1.365711@3] edt_ft5x06 3-0038: touchscreen probe failed
[    1.366576@3] rtc-hym8563 4-0051: no valid clock/calendar values available
[    1.366788@3] rtc-hym8563 4-0051: rtc core: registered hym8563 as rtc0
[    1.367163@3] i2c /dev entries driver
[    1.367949@3] IR NEC protocol handler initialized
[    1.367967@3] IR RC5(x/sz) protocol handler initialized
[    1.367984@3] IR RC6 protocol handler initialized
[    1.367999@3] IR JVC protocol handler initialized
[    1.368015@3] IR Sony protocol handler initialized
[    1.368031@3] IR SANYO protocol handler initialized
[    1.368047@3] IR Sharp protocol handler initialized
[    1.368062@3] IR MCE Keyboard/mouse protocol handler initialized
[    1.368079@3] IR XMP protocol handler initialized
[    1.368191@3] usbcore: registered new interface driver uvcvideo
[    1.368209@3] USB Video Class driver (1.1.1)
[    1.368312@3] usbcore: registered new interface driver cx231xx
[    1.368332@3] md: linear personality registered for level -1
[    1.368721@3] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[    1.368940@3] device-mapper: verity-avb: AVB error handler initialized with vbmeta device:
[    1.368990@3] Bluetooth: HCI UART driver ver 2.3
[    1.369009@3] Bluetooth: HCI UART protocol H4 registered
[    1.370423@3] ledtrig-cpu: registered to indicate activity on CPUs
[    1.370884@3] hidraw: raw HID events driver (C) Jiri Kosina
[    1.371172@3] usbcore: registered new interface driver usbhid
[    1.371191@3] usbhid: USB HID core driver
[    1.371642@3] meson_cpufreq_init: ignor dsu clk!
[    1.371662@3] meson_cpufreq_init: ignor dsu pre parent clk!
[    1.371716@3] value of voltage_tolerance 0
[    1.371733@3] meson_cpufreq_init:don't find the node <dynamic_gp1_clk>
[    1.371750@3] value of gp1_clk_target 0
[    1.372470@3] cpu cpu0: meson_cpufreq_init: CPU 0 initialized
[    1.373179@3] meson_cpufreq_init: ignor dsu clk!
[    1.373198@3] meson_cpufreq_init: ignor dsu pre parent clk!
[    1.373301@3] value of voltage_tolerance 0
[    1.373319@3] meson_cpufreq_init:don't find the node <dynamic_gp1_clk>
[    1.373336@3] value of gp1_clk_target 0
[    1.374348@3] cpu cpu2: meson_cpufreq_init: CPU 2 initialized
[    1.375002@3] ff803000.serial: clock gate not found
[    1.375038@3] meson_uart ff803000.serial: ==uart0 reg addr = ffffff8008825000
[    1.375070@3] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 25, base_baud = 1500000) is a meson_uart
[    1.375088@3] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
[    4.059966@3] console [ttyS0] enabled
[    4.063843@3] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008827000
[    4.070730@3] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 34, base_baud = 1500000) is a meson_uart
[    4.080684@3] amlogic-new-usb2-v2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008829000
[    4.091059@3] amlogic-new-usb3-v2 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff8008835080
[    4.103013@3] gpio-keypad gpio_keypad: power key(116) registed.
[    4.107695@3] input: gpio_keypad as /devices/platform/gpio_keypad/input/input1
[    4.114920@3] meson-remote: Driver init
[    4.118710@3] meson-remote: remote_probe
[    4.122541@3] meson-remote ff808040.rc: protocol = 0x1
[    4.127648@3] meson-remote ff808040.rc: don't find the node <led_blink>
[    4.134235@3] meson-remote ff808040.rc: led_blink = 0
[    4.139263@3] meson-remote ff808040.rc: don't find the node <led_blink_frq>
[    4.146195@3] meson-remote ff808040.rc: led_blink_frq  = 100
[    4.151835@3] meson-remote ff808040.rc: platform_data irq =33
[    4.157563@3] meson-remote ff808040.rc: custom_number = 1
[    4.162930@3] meson-remote ff808040.rc: ptable->map_size = 13
[    4.168643@3] meson-remote ff808040.rc: ptable->custom_name = khadas-ir
[    4.175227@3] meson-remote ff808040.rc: ptable->custom_code = 0xff00
[    4.181553@3] meson-remote ff808040.rc: ptable->release_delay = 80
[    4.187709@3] meson-remote ff808040.rc: default protocol = 0x1 and id = 0
[    4.194468@3] meson-remote ff808040.rc: reg=0x0, val=0x1f40190
[    4.200272@3] meson-remote ff808040.rc: reg=0x4, val=0x12c00c8
[    4.206080@3] meson-remote ff808040.rc: reg=0x8, val=0x960050
[    4.211799@3] meson-remote ff808040.rc: reg=0xc, val=0x480028
[    4.217519@3] meson-remote ff808040.rc: reg=0x10, val=0x70fa0013
[    4.223498@3] meson-remote ff808040.rc: reg=0x18, val=0x8616800
[    4.229392@3] meson-remote ff808040.rc: reg=0x1c, val=0x9f00
[    4.235026@3] meson-remote ff808040.rc: reg=0x20, val=0x0
[    4.240399@3] meson-remote ff808040.rc: reg=0x24, val=0x0
[    4.245772@3] meson-remote ff808040.rc: reg=0x28, val=0x0
[    4.251349@3] input: aml_keypad as /devices/platform/ff808040.rc/input/input2
[    4.258443@3] meson-remote: IR XMP protocol handler initialized
[    4.264303@3] efuse efuse:  open efuse clk gate error!!
[    4.269387@3] efusekeynum: 1
[    4.272215@3] efusekeyname:             mac  offset:     0   size:     6
[    4.278691@3] efuse efuse: probe OK!
[    4.283145@3] ion_dev soc:ion_dev: assigned reserved memory node linux,ion-dev
[    4.289617@3] ge2d: ge2d_init_module
[    4.293007@3] ge2d: ge2d_dev major:509
[    4.296758@3] ge2d: clock source clk_ge2d_gate ffffffc09ace2980
[    4.302562@3] ge2d: clock clk_ge2d source ffffffc09ace2a00
[    4.308012@3] ge2d: clock source clk_vapb_0 ffffffc09ace2a80
[    4.313638@3] ge2d: ge2d init clock is 500000000 HZ, VPU clock is 666666656 HZ
[    4.320877@3] ge2d: ge2d clock is 499 MHZ
[    4.324819@3] ge2d: find address resource
[    4.328806@3] ge2d: map io source 0x00000000ff940000,size=65536 to 0xffffff8008a10000
[    4.336601@3] ge2d: reserved mem init failed
[    4.340846@3] ge2d: ge2d: pdev=ffffffc09b1cec00, irq=41, clk=ffffffc09ace2980
[    4.347972@3] ge2d: ge2d start monitor
[    4.351712@4] ge2d: ge2d workqueue monitor start
[    4.351885@3] [tsync_pcr_init]init success.
[    4.351970@3] amvideom vsync irq: 42
[    4.352254@3] create_ge2d_work_queue video task ok
[    4.352273@3] fb: osd_init_module
[    4.352424@3] fb: viu vsync irq: 42
[    4.352431@3] fb: viu2 vsync irq: 51
[    4.352477@3] 0x000000db:Y=db,U=0,V=0
[    4.352478@3] 0x000000dc:Y=dc,U=0,V=0
[    4.352479@3] 0x000000dd:Y=dd,U=0,V=0
[    4.352480@3] 0x000000de:Y=de,U=0,V=0
[    4.352481@3] 0x000000df:Y=df,U=0,V=0
[    4.352482@3] 0x000000e0:Y=e0,U=0,V=0
[    4.356325@3] fb: osd_rdma_init: rdma_table p=0xa0610000,op=0xa0610000 , v=0xffffff8008883000
[    4.356345@3] rdma_register, rdma_table_addr ffffff8008885000 rdma_table_addr_phy a0611000 reg_buf ffffffc09b03c000
[    4.356346@3] rdma_register success, handle 3 table_size 4096
[    4.356348@3] fb: osd_rdma_init:osd rdma handle = 3.
[    4.356355@3] fb: mem_size: 0x800000
[    4.356355@3] fb: mem_size: 0x4b80000
[    4.356356@3] fb: mem_size: 0x100000
[    4.356357@3] fb: mem_size: 0x100000
[    4.356358@3] fb: mem_size: 0x800000
[    4.356383@3] meson-fb meson-fb: assigned reserved memory node linux,meson-fb
[    4.356384@3] fb: reserved memory base:0x000000007f800000, size:800000
[    4.356465@3] fb: fb def : 1920 1080 1920 2160 32
[    4.356466@3] fb: init fbdev bpp is:32
[    4.470335@5] fb: malloc_osd_memory, cma:ffffff800ace00d8
[    4.470337@5] fb: malloc_osd_memory, 1228, base:0x000000007f800000, size:8388608
[    4.470357@5] fb: use ion buffer for fb memory, fb_index=0
[    4.470359@5] fb: OSD0 as afbcd mode,afbc_type=2
[    4.491374@5] meson-fb meson-fb: create ion_client ffffffc09b0cb480, handle=ffffffc09ae7cb40
[    4.491378@5] meson-fb meson-fb: ion memory(0): created fb at 0x00000000e5800000, size 75 MiB
[    4.491380@5] fb:  0, phy: 0x00000000e5800000, vir:0xffffff800ada0000, size=77312K
[    4.491380@5]
[    4.491383@5] fb: Frame buffer memory assigned at
[    4.491384@5] fb:  0, phy: 0x00000000e5800000, vir:0xffffff800ada0000, size=77312K
[    4.491384@5]
[    4.491385@5] fb:  0, phy: 0x00000000e5800000, vir:0xffffff800ada0000, size=77312K
[    4.491385@5]
[    4.491387@5] fb: logo_index=0,fb_index=0
[    4.491388@5] fb: ---------------clear fb0 memory ffffff800ada0000
[    4.503635@5] fb: osd[0] canvas.idx =0x40
[    4.503636@5] fb: osd[0] canvas.addr=0xe5800000
[    4.503637@5] fb: osd[0] canvas.width=7680
[    4.503638@5] fb: osd[0] canvas.height=2160
[    4.503639@5] fb: osd[0] frame.width=1920
[    4.503640@5] fb: osd[0] frame.height=1080
[    4.503641@5] fb: osd[0] out_addr_id =0x1
[    6.555980@5] Console: switching to colour frame buffer device 240x67
[    7.701260@5] fb: osd[0] enable: 1 (swapper/0)
[    8.725641@5] fb: set osd0 reverse as NONE
[    9.749262@5] fb: osd probe OK
[    9.749420@5] hdmitx: hdcp: hdmitx_hdcp_init
[    9.751287@5] vout: vout2: create vout2 attribute OK
[    9.755938@5] vout: vout2: vout2_fops_create OK
[    9.760488@5] vout: vout2: clktree_init
[    9.764196@5] vout: vout2: register server: nulldisp_vout2_server
[    9.770324@5] vout: vout2: init mode null set ok
[    9.774856@5] vout: vout2: aml_vout2_probe OK
[    9.779256@5] DI: di_module_init ok.
[    9.782743@5] DI: di_module_init: major 506
[    9.787082@5] deinterlace deinterlace: assigned reserved memory node linux,di_cma
[    9.794359@5] DI: CMA size 0x2800000.
[    9.798009@5] pre_irq:66
[    9.800508@5] post_irq:67
[    9.803109@5] DI: di_probe allocate rdma channel 0.
[    9.807965@5] di_get_vpu_clkb: get clk vpu error.
[    9.812649@5] DI: vpu clkb <334000000, 667000000>
[    9.817342@5] DI:enable vpu clkb.
[    9.820617@5] 0x000000e1:Y=e1,U=0,V=0
[    9.824256@5] 0x000000e2:Y=e2,U=0,V=0
[    9.827895@5] 0x000000e3:Y=e3,U=0,V=0
[    9.831534@5] 0x000000f0:Y=f0,U=0,V=0
[    9.835175@5] 0x000000f1:Y=f1,U=0,V=0
[    9.838814@5] 0x000000f2:Y=f2,U=0,V=0
[    9.842455@5] 0x000000f3:Y=f3,U=0,V=0
[    9.846094@5] 0x000000f4:Y=f4,U=0,V=0
[    9.849734@5] 0x000000f5:Y=f5,U=0,V=0
[    9.853374@5] 0x000000f6:Y=f6,U=0,V=0
[    9.857013@5] 0x000000f7:Y=f7,U=0,V=0
[    9.860655@5] 0x000000f8:Y=f8,U=0,V=0
[    9.864294@5] 0x000000f9:Y=f9,U=0,V=0
[    9.867934@5] 0x000000fa:Y=fa,U=0,V=0
[    9.871574@5] 0x000000fb:Y=fb,U=0,V=0
[    9.875214@5] 0x000000fc:Y=fc,U=0,V=0
[    9.878857@5] 0x000000fd:Y=fd,U=0,V=0
[    9.882494@5] 0x000000fe:Y=fe,U=0,V=0
[    9.886134@5] 0x000000ff:Y=ff,U=0,V=0
[    9.889774@5] 0x0000003a:Y=3a,U=0,V=0
[    9.893414@5] 0x0000003b:Y=3b,U=0,V=0
[    9.897050@5] 0x0000003c:Y=3c,U=0,V=0
[    9.900695@5] 0x0000003d:Y=3d,U=0,V=0
[    9.904334@5] DI: support post write back 61.
[    9.908761@5] DI: di_probe:Di use HRTIMER
[    9.912712@5] di_probe:ok
[    9.915303@5] vdin_drv_init: major 505
[    9.919146@5] rdma_register, rdma_table_addr ffffff800888d000 rdma_table_addr_phy a0612000 reg_buf ffffffc098d4f600
[    9.929392@5] rdma_register success, handle 4 table_size 512
[    9.935017@5] vdin_drv_probe:vdin.0 rdma hanld 4.
[    9.939796@5] vdin vdin0: assigned reserved memory node linux,vdin0_cma
[    9.946284@5]
[    9.946284@5]  vdin memory resource done.
[    9.951924@5] vdin0 cma_mem_size = 64 MB
[    9.955817@5] vdin0 irq: 39 rdma irq: 2
[    9.959633@5] set_canvas_manual = 0
[    9.963096@5] no urgent_en found
[    9.966310@5] get fclk_div5 err
[    9.969427@5] vdin_drv_probe: vdin cannot get msr clk !!!
[    9.974810@5] vdin_drv_probe: driver initialized ok
[    9.979694@5] rdma_register, rdma_table_addr ffffff80088a1000 rdma_table_addr_phy a0613000 reg_buf ffffffc098d4f800
[    9.990054@5] rdma_register success, handle 5 table_size 512
[    9.995683@5] vdin_drv_probe:vdin.1 rdma hanld 5.
[   10.000447@5] vdin vdin1: assigned reserved memory node linux,vdin1_cma
[   10.006952@5]
[   10.006952@5]  vdin memory resource done.
[   10.012586@5] vdin1 cma_mem_size = 64 MB
[   10.016493@5] vdin1 irq: 40 rdma irq: 4
[   10.020300@5] set_canvas_manual = 0
[   10.023763@5] no urgent_en found
[   10.026975@5] get fclk_div5 err
[   10.030094@5] vdin_drv_probe: vdin cannot get msr clk !!!
[   10.035465@5] vdin_debugfs_init only support debug vdin0 1
[   10.040925@5] vdin_drv_probe: driver initialized ok
[   10.045842@5] vdin_drv_init: vdin driver init done
[   10.050546@5] [viuin..]viuin_init_module viuin module init
[   10.056152@5] [viuin..]viuin_probe probe ok.
[   10.060515@5] [RX]-hdmirx: hdmirx_init.
[   10.064064@5] ESM HLD: Initializing...
[   10.067849@5] tvin_afe: tvafe_drv_init: major 503
[   10.072623@5] tvin_afe: tvafe_drv_init.
[   10.076378@5] tvafe_vbi: vbi: vbi_init.
[   10.080207@5] amvdec_csi module: init.
[   10.083824@5] amvdec_csi_init_module:major 501
[   10.088334@5] amvdec_csi module: init. ok
[   10.092233@5] amlvid:info: amlvideo_init called[   10.096562@5] amlvid:info: amlvideo_create_instance called
[   10.102027@5] amlvid:info: v4l2_dev.name=:amlvideo-000
[   10.107206@5] amlvideo-000: V4L2 device registered as video10
[   10.112938@5] amlvideo2 probe called
[   10.116411@5] amlvideo2_create_node[   10.119779@5] amlvideo2: V4L2 device registered as video11
[   10.125176@5] amlvideo2 probe called
[   10.128716@5] amlvideo2_create_node[   10.132079@5] amlvideo2: V4L2 device registered as video12
[   10.137496@5] PPMGRDRV: warn: ppmgr module init func called
[   10.143093@5] PPMGRDRV: info: ppmgr_driver_probe called
[   10.148252@5] Reserved memory: failed to init DMA memory pool at 0x00000000e3000000, size 0 MiB
[   10.156890@5] PPMGRDRV: info: ppmgr_dev major:500
[   10.161880@5] ionvideo-000: V4L2 device registered as video13
[   10.167288@5] ionvid: info: Video Technology Magazine Ion Video
[   10.173180@5] ionvid: info: Capture Board ver 1.0 successfully loaded
[   10.179697@5] picdec: picdec_driver_probe called.
[   10.184367@5] picdec: probe of picdec failed with error -22
[   10.189917@5] videosync_create_instance dev_s ffffffc098df1400,dev_s->dev ffffffc07f1ba500
[   10.198052@5] videosync_create_instance reg videosync.0
[   10.203290@5] aml_vecm_init:module init
[   10.203293@2] videosync_thread started
[   10.210893@5]
[   10.210893@5]  VECM probe start
[   10.215677@5] vlock_status_init vlock_en:0
[   10.219661@5] Can't find  wb_sel.
[   10.222923@5] hdr:Can't find  cfg_en_osd_100.
[   10.227258@5] Can't find  tx_op_color_primary.
[   10.231679@5] amlogic, vecm[   10.234277@5] vlock dt support: 1
[   10.237569@5] vlock dt new_fsm: 0
[   10.240862@5] vlock dt hwver: 0
[   10.243983@5] vlock dt phlock_en: 0
[   10.247449@5] Can't find  vlock_en.
[   10.250920@5] Can't find  vlock_mode.
[   10.254556@5] Can't find  vlock_pll_m_limit.
[   10.258805@5] Can't find  vlock_line_limit.
[   10.262966@5] param_config vlock_en:0
[   10.266614@5] request amvecm_vsync2_irq successful
[   10.271372@5] aml_vecm_probe: ok
[   10.274598@5] amdolby_vision_init:module init
[   10.279049@5]
[   10.279049@5]  amdolby_vision probe start & ver: 20181220
[   10.285933@5]
[   10.285933@5]  cpu_id=2 tvmode=0
[   10.290854@5] dolby_vision_init_receiver(dvel)
[   10.295206@5] dolby_vision_init_receiver: dvel
[   10.299709@5] amdolby_vision_probe: ok
[   10.303375@5] prime_sl module init
[   10.306907@5] reg base = ffffff80088ec000
[   10.310761@5] gdc ff950000.gdc: assigned reserved memory node linux,gdc_cma
[   10.317945@5] vm_init .
[   10.320540@5] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
[   10.328518@5] meson-mmc: >>>>>>>>hostbase ffffff80088f4000, dmode
[   10.334367@5] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[   10.339931@5] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[   10.456637@5] meson-aml-mmc ffe07000.emmc: divider requested rate 200000000 != actual rate 199999997: ret=0
[   10.462124@5] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
[   10.468094@5] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
[   10.475118@5] meson-mmc: Data 1 aligned delay is 0
[   10.479884@5] meson-mmc: emmc: clk 199999997 tuning start
[   10.486127@5] meson-mmc: emmc: rx_tuning_result[0] = 40
[   10.490565@5] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[   10.498541@5] meson-mmc: emmc: rx_tuning_result[2] = 40
[   10.503751@5] meson-mmc: emmc: rx_tuning_result[3] = 40
[   10.508942@5] meson-mmc: emmc: rx_tuning_result[4] = 40
[   10.513247@5] meson-mmc: [prev_map] fixed_adj_win_map:29
[   10.518538@5] meson-mmc: [0]=1
[   10.521570@5] meson-mmc: [1]=0
[   10.524595@5] meson-mmc: [2]=1
[   10.527633@5] meson-mmc: [3]=1
[   10.530669@5] meson-mmc: [4]=1
[   10.533700@5] meson-mmc: [_find_fixed_adj_valid_win]retry test fixed adj...
[   10.540637@5] meson-mmc: step:4, delay1:0x4104104, delay2:0x4004104
[   10.547771@5] meson-mmc: emmc: rx_tuning_result[0] = 40
[   10.552179@5] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[   10.560170@5] meson-mmc: emmc: rx_tuning_result[2] = 40
[   10.565362@5] meson-mmc: emmc: rx_tuning_result[3] = 40
[   10.570546@5] meson-mmc: emmc: rx_tuning_result[4] = 40
[   10.574872@5] meson-mmc: [_find_fixed_adj_valid_win]retry test fixed adj...
[   10.581804@5] meson-mmc: step:8, delay1:0x8208208, delay2:0x8008208
[   10.588933@5] meson-mmc: emmc: rx_tuning_result[0] = 40
[   10.593343@5] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[   10.601321@5] meson-mmc: emmc: rx_tuning_result[2] = 40
[   10.606525@5] meson-mmc: emmc: rx_tuning_result[3] = 40
[   10.611697@5] meson-mmc: emmc: rx_tuning_result[4] = 40
[   10.616033@5] meson-mmc: [_find_fixed_adj_valid_win]retry test fixed adj...
[   10.622970@5] meson-mmc: step:12, delay1:0xc30c30c, delay2:0xc00c30c
[   10.630199@5] meson-mmc: emmc: rx_tuning_result[0] = 40
[   10.634595@5] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[   10.642587@5] meson-mmc: emmc: rx_tuning_result[2] = 40
[   10.647777@5] meson-mmc: emmc: rx_tuning_result[3] = 40
[   10.652986@5] meson-mmc: emmc: rx_tuning_result[4] = 40
[   10.657292@5] meson-mmc: [_find_fixed_adj_valid_win]retry test fixed adj...
[   10.664224@5] meson-mmc: step:16, delay1:0x10410410, delay2:0x10010410
[   10.671611@5] meson-mmc: emmc: rx_tuning_result[0] = 40
[   10.676807@5] meson-mmc: emmc: rx_tuning_result[1] = 40
[   10.681225@5] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[   10.689215@5] meson-mmc: emmc: rx_tuning_result[3] = 40
[   10.694405@5] meson-mmc: emmc: rx_tuning_result[4] = 40
[   10.698714@5] meson-mmc: [>>>>>>>>bitmap_xor_dst] fixed_adj_win_map:4
[   10.705129@5] meson-mmc: [0]=0
[   10.708159@5] meson-mmc: [1]=0
[   10.711195@5] meson-mmc: [2]=1
[   10.714231@5] meson-mmc: [3]=0
[   10.717259@5] meson-mmc: [4]=0
[   10.720293@5] meson-mmc: [_find_fixed_adj_valid_win] fir_adj:2
[   10.726101@5] meson-mmc: [>>>>>>>>prev_map_range] fixed_adj_win_map:239
[   10.732688@5] meson-mmc: [2]=1
[   10.735719@5] meson-mmc: [3]=1
[   10.738752@5] meson-mmc: [4]=1
[   10.741793@5] meson-mmc: [0]=1
[   10.744815@5] meson-mmc: [1]=0
[   10.747853@5] meson-mmc: left:3, right:0, mid:4, size:4
[   10.753056@5] meson-mmc: step:0, delay1:0x0, delay2:0x0
[   10.758254@5] meson-mmc: emmc: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x42000
[   10.766662@5] meson-mmc: delay1:0x0, delay2:0x0
[   10.771331@5] emmc: new HS200 MMC card at address 0001
[   10.776281@5] emmc: clock 199999997, 8-bit-bus-width
 [   10.781556@5] mmcblk0: emmc:0001 BJTD4R 29.1 GiB
[   10.786101@5] mmcblk0boot0: emmc:0001 BJTD4R partition 1 4.00 MiB
[   10.792176@5] mmcblk0boot1: emmc:0001 BJTD4R partition 2 4.00 MiB
[   10.798252@5] mmcblk0rpmb: emmc:0001 BJTD4R partition 3 4.00 MiB
[   10.804667@5] meson-mmc: Enter aml_emmc_partition_ops
[   10.809645@5] meson-mmc: [mmc_read_partition_tbl] mmc read partition OK!
[   10.815801@5] meson-mmc: add_emmc_partition
[   10.820037@5] meson-mmc: [mmcblk0p01]           bootloader  offset 0x000000000000, size 0x000000400000
[   10.829391@5] meson-mmc: [mmcblk0p02]             reserved  offset 0x000002400000, size 0x000004000000
[   10.838744@5] meson-mmc: [mmcblk0p03]                  env  offset 0x000006c00000, size 0x000000800000
[   10.848106@5] meson-mmc: [mmcblk0p04]                 logo  offset 0x000007c00000, size 0x000000800000
[   10.857468@5] meson-mmc: [mmcblk0p05]              ramdisk  offset 0x000008c00000, size 0x000002000000
[   10.866822@5] meson-mmc: [mmcblk0p06]               rootfs  offset 0x00000b400000, size 0x00073c800000
[   10.876135@5] card key: card_blk_probe.
[   10.879939@5] emmc_key_init:183 emmc key lba_start:0x12020,lba_end:0x12220
[   10.886789@5] emmc key: emmc_key_init:205 ok.
[   10.891117@5] meson-mmc: amlmmc_dtb_init: register dtb chardev[   10.898637@5] meson-mmc: calc de0f5855, store de0f5855
[   10.903727@5] meson-mmc: calc de0f5855, store de0f5855
[   10.906977@5] meson-mmc: total valid 2
[   10.910771@5] meson-mmc: amlmmc_dtb_init: register dtb chardev OK[   10.916615@5] meson-mmc: Exit aml_emmc_partition_ops OK.
[   11.317258@2] vout: aml_tvout_mode_work: monitor_timeout
[   70.677258@5] fb: mem_free_work, free memory: addr:800000

hyphop · February 19, 2020, 12:36pm

plz ! try boot up Krescue from SD and make online image instalation for latest ubuntu

PS: what about other OS ?

rider · February 19, 2020, 12:43pm

what does “online image instalation for latest ubuntu” means?

i didn’t try other OS as my other vim3 pro is booting from this image with no problem

Vladimir.v.v · February 19, 2020, 1:46pm

Hyphop only wants to understand, on this vim, only this OS has a problem, or problems with other OS also take place.

Are you familiar with a tool like Krescue?

rider · February 19, 2020, 4:01pm

I used Krescue to clone images,i did clone from “good” vim3 pro to “bad” vim 3 pro,but result are the same.
I didn’t see any option in Krescue menu for “online image instalation”.

hyphop · February 19, 2020, 4:49pm

u can make broken clone for example some trash sd card can have same issue
plz write last version krescue from there https://dl.khadas.com/Firmware/Krescue/dump/
insert ethernet cable to VIM board => image_write_to emmc => download => check_online_images => download => write image => reboot

Vladimir.v.v · February 19, 2020, 8:23pm

Hyphop, what is the algorithm for installing the OS through Krescue, is it just installing the OS, or does it include fast emmc formatting in this process?

numbqq · February 20, 2020, 1:21am

What issues do you think the eMMC have? Can you boot into the ubuntu command line?
I didn’t see the eMMC errors.

rider · February 20, 2020, 8:30am

the issues that is see:
cfgload: start ...
cfgload: reading /boot.ini from mmc 0:1 ...
card out
** Bad device mmc 0 **
cfgload: no /boot.ini or empty file on mmc 0:1
cfgload: reading /boot/boot.ini from mmc 0:1 ...
card out
** Bad device mmc 0 **
cfgload: no /boot/boot.ini or empty file on mmc 0:1
cfgload: reading /boot.ini from mmc 1:1 ...
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
cfgload: no /boot.ini or empty file on mmc 1:1
cfgload: reading /boot/boot.ini from mmc 1:1 ...
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
cfgload: no /boot/boot.ini or empty file on mmc 1:1
cfgload: reading /boot/boot.ini from mmc 1:5 ...
8183 bytes read in 4 ms (2 MiB/s)
cfgload: applying boot.ini...
[#] Script a:d3e3e140 l:8163 c:0 s:0 - run
Starting boot.ini...
saradc: 0x28a, hw_ver: 0x32 (VIM3.V12)
uboot type: vendor
Scanning mmc 0:1...
card out
** Bad device mmc 0 **
Scanning mmc 0:5...
card out
** Bad device mmc 0 **
Scanning mmc 1:1...
** Unrecognized filesystem type **
Scanning mmc 1:5...

I don’t know if this is normal, I’m no expert in linux.
i cant log in to ubuntu command line, its just halt on the last line in the log that i posted every time.

numbqq · February 20, 2020, 8:49am

This log is OK.

Which image you use? Have you tried other images? How you supply the power?

rider · February 20, 2020, 4:26pm

using the ethernet cable i cant get it to connect to the internet .
running krescue shell -> ifconfig shows only “lo” and “usb” interfaces are avilable, but no eth0.

rider · February 20, 2020, 4:27pm

I’m using Ubuntu server latest ,i didn’t try other images
using original power supply and cable from khadas.

hyphop · February 20, 2020, 4:55pm

its very strange plz!! show me more info from booted krescue

cat /tmp/headers_sd_fat
devinfo
dmesg

try next step

mmc_erase full - clear emmc & reboot krescue from SD again

Vladimir.v.v · February 20, 2020, 5:01pm

I’m here on the forum for these words, I came under the ice rink
but, I trust you, and always try to read your posts carefully!

rider · February 20, 2020, 5:18pm

hyphop · February 21, 2020, 1:53am

look like Ethernet port is defective
check boot source >

grep -o booted=.... /proc/cmdline

check emmc

mmc_erase full - blank emmc
[i] full clean mode 29.1G - 31268536320 bytes! plz wait…
29.1GiB 0:07:04 [70.3MiB/s] [================================>] 100%
pv /dev/mmcblk2 | md5sum
29.1GiB 0:04:02 [ 123MiB/s] [================================>] 100%
0ce1ec5fd942704583c3069446b76efe -

if u have it emmc is OK

NOTE: if your VIM usb cable connected to working machine - u can use usb-ethernet for krescue ssh connection

rider · February 23, 2020, 7:51am

booted= hw
md5sum is OK.
… so what is the next step?

hyphop · February 23, 2020, 12:51pm

ok ! reboot device start krescue and install any os! (u can predownload images https://dl.khadas.com/Firmware/Krescue/images/ to sd )
for example try ! openwrt or coreelec its not heavy for test your device again!