Edp显示有问题，麻烦帮忙看看

monkey_m4 · July 24, 2022, 8:15am

改了DTS 也改了MK 重新刷了固件能亮但是显示有问题
edp dp 为主屏 HDMI 为副屏
麻烦帮忙看看参数是不是设置错了或者是我屏线做错了
屏是 B133zan02.A和N133DCE-GP1 两个都试了一样的画面

kernel/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge-android.dts

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (c) 2018 Fuzhou Rockchip Electronics Co., Ltd
 */

/dts-v1/;

#include "rk3399-khadas-edge.dtsi"
#include <dt-bindings/sensor-dev.h>
#include <dt-bindings/input/input.h>

/ {
	compatible = "Khadas,edge", "rockchip,rk3399";
	
    khadas-matrix-keypad {
		status = "okay";
		compatible = "khadas-matrix-keypad";
		row_col_gpio =
				<&gpio0 10 GPIO_ACTIVE_HIGH>,
				<&gpio0 11 GPIO_ACTIVE_HIGH>,
				<&gpio0 12 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&matrix_gpio>;
		debounce-delay-ms = <10>;
		col-scan-delay-us = <10>;
		linux,no-autorepeat;
	};



	edp_panel: edp-panel {
		compatible = "simple-panel";
		backlight = <&backlight>;
                bus-format = <MEDIA_BUS_FMT_RGB888_1X24>;
		power-supply = <&vcc3v3_s0>;
	        reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_HIGH>; /* GPIO4_D4 */
	        enable-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_HIGH>; /* GPIO4_D5 */
		prepare-delay-ms = <30>;
		enable-delay-ms = <30>;		
		ports {
			panel_in_edp: endpoint {
		      	remote-endpoint = <&edp_out_panel>;
	      		};
		};
		display-timings {
			native-mode = <&timing0>;

			timing0: timing0 {
				clock-frequency = <533010000>;
				hactive = <3840>;
				vactive = <2160>;
				hfront-porch = <48>;
				hsync-len = <2>;
				hback-porch = <110>;
				vfront-porch = <10>;
				vsync-len = <2>;
				vback-porch = <50>;
				hsync-active = <0>;
				vsync-active = <0>;
				de-active = <0>;
				pixelclk-active = <0>;
			};
		};
	};

	rt5651-sound {
		status = "okay";
		compatible = "simple-audio-card";

		pinctrl-names = "default";
		pinctrl-0 = <&rt5651_hpdet>;


		simple-audio-card,format = "i2s";
		simple-audio-card,name = "realtek,rt5651-codec";
		simple-audio-card,mclk-fs = <256>;
		simple-audio-card,hp-det-gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
		simple-audio-card,widgets =
			"Microphone", "Mic Jack",
			"Headphone", "Headphone Jack";
		simple-audio-card,routing =
			"Mic Jack", "MICBIAS1",
			"IN1P", "Mic Jack",
			"Headphone Jack", "HPOL",
			"Headphone Jack", "HPOR";
		simple-audio-card,cpu {
			sound-dai = <&i2s1>;
		};
		simple-audio-card,codec {
			sound-dai = <&rt5651>;
		};
	};
};


&fusb0 {
	status = "okay";
	max-input-voltage = <13000000>;
	max-input-current = <6000000>;
	charge-dev = <&bq25703>;
};

&fusb1 {
	status = "okay";
	max-input-voltage = <13000000>;
	max-input-current = <6000000>;
	charge-dev = <&bq25703>;
};

&i2s1 {
    #sound-dai-cells = <0>;
    /* rockchip,bclk-fs = <64>; */
    status = "okay";
};

&isp0_mmu {
	status = "okay";
};

&isp1_mmu {
	status = "okay";
};

&i2c0 {
	status = "okay";
	i2c-scl-rising-time-ns = <300>;
	i2c-scl-falling-time-ns = <15>;
};

&i2c1 {
	status = "okay";
	i2c-scl-rising-time-ns = <300>;
	i2c-scl-falling-time-ns = <15>;

	rt5651: rt5651@1a {
		#sound-dai-cells = <0>;
		compatible = "rockchip,rt5651";
		reg = <0x1a>;
		clocks = <&cru SCLK_I2S_8CH_OUT>;
		clock-names = "mclk";
		pinctrl-names = "default";
		pinctrl-0 = <&i2s_8ch_mclk>;
		status = "okay";
	};
};

&i2c6 {
	status = "okay";

	vm149c: vm149c@0c {
		compatible = "silicon touch,vm149c";
		status = "okay";
		reg = <0x0c>;
		rockchip,camera-module-index = <0>;
		rockchip,camera-module-facing = "back";
	};
	
	imx214b: imx214b@10 {
		compatible = "sony,imx214";
		status = "okay";
		reg = <0x10>;
		clocks = <&cru SCLK_CIF_OUT>;
		clock-names = "xvclk";
		/* avdd-supply = <>; */
		/* dvdd-supply = <>; */
		/* dovdd-supply = <>; */
		/* reset-gpios = <>; */
		pwdn-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
		reset-gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "rockchip,camera_default";
		pinctrl-0 = <&cif_clkout>;
		rockchip,camera-module-index = <0>;
		rockchip,camera-module-facing = "back";
		rockchip,camera-module-name = "YG9626-S600Y7-C";
		rockchip,camera-module-lens-name = "LG-50013A7";
		lens-focus = <&vm149c>;
		port {
			ucam_out0: endpoint {
				remote-endpoint = <&mipi_in_ucam0>;
				//remote-endpoint = <&mipi_in_ucam1>;
				data-lanes = <1 2>;
			};
		};
	};	

	vm149c_front: vm149c_front@0c {
		compatible = "silicon touch,vm149c";
		status = "okay";
		reg = <0x0c>;
		rockchip,camera-module-index = <1>;
		rockchip,camera-module-facing = "front";		
	};
	
	imx214f: imx214f@10 {
		compatible = "sony,imx214";
		status = "okay";
		reg = <0x10>;
		clocks = <&cru SCLK_CIF_OUT>;
		clock-names = "xvclk";
		/* avdd-supply = <>; */
		/* dvdd-supply = <>; */
		/* dovdd-supply = <>; */
		/* reset-gpios = <>; */
		pwdn-gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
		reset-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "rockchip,camera_default";
		pinctrl-0 = <&cif_clkout>;
		rockchip,camera-module-index = <1>;
		rockchip,camera-module-facing = "front";
		rockchip,camera-module-name = "YG9626-S600Y7-C";
		rockchip,camera-module-lens-name = "LG-50013A7";
		lens-focus = <&vm149c_front>;
		port {
			ucam_out1: endpoint {
				//remote-endpoint = <&mipi_in_ucam0>;
				remote-endpoint = <&mipi_in_ucam1>;
				data-lanes = <1 2>;
			};
		};
	};	
};

&i2c7 {
	status = "okay";

	icm20602_acc: icm_acc@68 {
		compatible = "icm20602_acc";
		reg = <0x68>;
		irq-gpio = <&gpio0 8 IRQ_TYPE_LEVEL_LOW>; /* GPIO0_B0 */
		irq_enable = <0>;
		poll_delay_ms = <30>;
		type = <SENSOR_TYPE_ACCEL>;
		layout = <9>;
	};

	icm20602_gyro: icm_gyro@68 {
		compatible = "icm20602_gyro";
		reg = <0x68>;
		irq_enable = <0>;
		poll_delay_ms = <30>;
		type = <SENSOR_TYPE_GYROSCOPE>;
		layout = <7>;
	};
};

&i2c8 {
	status = "okay";
	i2c-scl-rising-time-ns = <600>;
	i2c-scl-falling-time-ns = <20>;

	apds9960@39 {
		compatible = "avago,apds9960";
		reg = <0x39>;
		interrupt-parent = <&gpio3>;
		interrupts = <RK_PB2 IRQ_TYPE_LEVEL_LOW>;
		led-r-gpio = <&gpio4 24 GPIO_ACTIVE_HIGH>;		
		pinctrl-names = "default";
		pinctrl-0 = <&apds_int_l>;
	};

	bq25703: bq25703@6b {
		compatible = "ti,bq25703";
		reg = <0x6b>;
		extcon = <&fusb0>, <&fusb1>;
		interrupt-parent = <&gpio1>;
		interrupts = <RK_PC7 IRQ_TYPE_LEVEL_LOW>; /* GPIO1_C7 */
		pinctrl-names = "default";
		pinctrl-0 = <&charger_ok>;
		ti,charge-current = <1500000>;
		ti,max-charge-voltage = <8500000>;
		ti,max-input-voltage = <20000000>;
		ti,max-input-current = <6000000>;
		ti,input-current-sdp = <500000>;
		ti,input-current-dcp = <2000000>;
		ti,input-current-cdp = <2000000>;
		ti,input-current-dc = <2000000>;
		ti,minimum-sys-voltage = <7400000>;
		ti,otg-voltage = <5000000>;
		ti,otg-current = <500000>;
		ti,input-current = <500000>;
		pd-charge-only = <0>;
		status = "okay";
	};

	cw2013: cw2013@62 {
		status = "okay";
		compatible = "cw201x";
		reg = <0x62>;
		bat_config_info = <0x15 0x7F 0x6E 0x66 0x65 0x5C 0x5B 0x59
				0x58 0x57 0x57 0x54 0x53 0x51 0x4B 0x48
				0x40 0x33 0x2A 0x26 0x23 0x25 0x2A 0x34
				0x45 0x4F 0x0C 0xCD 0x44 0x68 0x67 0x68
				0x6E 0x6F 0x6C 0x68 0x3A 0x10 0x8A 0x01
				0x01 0x54 0x52 0x87 0x8F 0x91 0x94 0x52
				0x82 0x8C 0x92 0x96 0x82 0xFF 0xFF 0xCB
				0x2F 0x7D 0x64 0xA5 0xB5 0x13 0x58 0x09>;
		monitor_sec = <5>;
		virtual_power = <0>;
		divider_res1 = <200>;
		divider_res2 = <200>;
		dc_det_gpio = <&gpio1 RK_PC7 GPIO_ACTIVE_HIGH>;
	};
};

&rk_key {
	enter-key {
		linux,code = <232>;
		label = "enter";
		rockchip,adc_value = <170>;
	};
};


&pwm3 {
	status = "okay";

	interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH 0>;
	compatible = "rockchip,remotectl-pwm";
	remote_pwm_id = <3>;
	handle_cpu_id = <1>;
	remote_support_psci = <1>;
	pinctrl-names = "default";
	pinctrl-0 = <&pwm3b_pin>;

	ir_key1 {
		rockchip,usercode = <0xff00>;
		rockchip,key_table =
			<0xeb   KEY_POWER>,
			<0xec   KEY_MENU>,
			<0xfc   KEY_UP>,
			<0xfd   KEY_DOWN>,
			<0xf1   KEY_LEFT>,
			<0xe5   KEY_RIGHT>,
			<0xf8   232>,
			<0xa7   KEY_VOLUMEDOWN>,
			<0xa3    388>,  //mouse func
			<0xa4    388>,  //mouse func
			<0xf4   KEY_VOLUMEUP>,
			<0xfe   KEY_BACK>,
			<0xb7   KEY_HOME>;

	};

};

&backlight {
	pwms = <&pwm1 0 25000 0>;
	status = "okay";
};


&pwm1 {
	status = "okay";
};

&cdn_dp {
	status = "okay";
};

&dp_in_vopl {
	status = "disabled";
};

&dp_in_vopb {
	status = "okay";
};

&hdmi_in_vopb {
	status = "okay";
};

&hdmi_in_vopl {
	status = "disabled";
};

&route_hdmi {
	status = "okay";
	connect = <&vopb_out_hdmi>;
};

&vopb {
	status = "okay";
	assigned-clocks = <&cru DCLK_VOP0_DIV>;
	assigned-clock-parents = <&cru PLL_VPLL>;
};

&vopl {
	status = "okay";
	assigned-clocks = <&cru DCLK_VOP1_DIV>;
	assigned-clock-parents = <&cru PLL_CPLL>;
};
&route_edp {
	status = "okay";
	connect = <&vopb_out_edp>;
};

&edp_in_vopb {
	status = "okay";
};

&edp_in_vopl {
	status = "disabled";
};

&edp {
	force-hpd;
	status = "okay";
	ports {
		edp_out: port@1 {
			reg = <1>;
			#address-cells = <1>;
			#size-cells = <0>;
			edp_out_panel: endpoint@0 {
				reg = <0>;
				remote-endpoint = <&panel_in_edp>;
			};
        };
    };
};

&i2c2 {
    status = "okay";
    i2c-scl-rising-time-ns = <600>;
    i2c-scl-falling-time-ns = <20>;

	ft5336@38 {
		compatible = "edt,edt-ft5336", "ft5x06";
		reg = <0x38>;
		interrupt-parent = <&gpio2>;
		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
		reset-gpio = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>; /* GPIO2_A3 */
		status = "okay";
	};
};

&pinctrl {
	matrix {
		matrix_gpio: matrix_gpio {
			rockchip,pins =
				<0 10 RK_FUNC_GPIO &pcfg_pull_up>,
				<0 11 RK_FUNC_GPIO &pcfg_pull_up>,
				<0 12 RK_FUNC_GPIO &pcfg_pull_up>;
		};
	};

	apds_int_l: apds-int-l {
		rockchip,pins = <3 10 RK_FUNC_GPIO &pcfg_pull_up>;
	};

	charger {
		charger_ok: charge-ok {
			rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_up>; /* GPIO1_C7 */
		};
	};

	rt5651 {
		rt5651_hpdet: rt5651-hpdet {
			rockchip,pins = <1 0 RK_FUNC_GPIO &pcfg_pull_up>; /* GPIO1_A0 */
		};
	};
};

&mipi_dphy_rx0 {
	status = "okay";

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
			reg = <0>;
			#address-cells = <1>;
			#size-cells = <0>;

			mipi_in_ucam0: endpoint@1 {
				reg = <1>;
				remote-endpoint = <&ucam_out0>;
				data-lanes = <1 2>;
			};
		};

		port@1 {
			reg = <1>;
			#address-cells = <1>;
			#size-cells = <0>;

			dphy_rx0_out: endpoint@0 {
				reg = <0>;
				remote-endpoint = <&isp0_mipi_in>;
			};
		};
	};
};

&rkisp1_0 {
	status = "okay";

	port {
		#address-cells = <1>;
		#size-cells = <0>;

		isp0_mipi_in: endpoint@0 {
			reg = <0>;
			remote-endpoint = <&dphy_rx0_out>;
		};
	};
};

&mipi_dphy_tx1rx1 {
	status = "okay";

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
			reg = <0>;
			#address-cells = <1>;
			#size-cells = <0>;

			mipi_in_ucam1: endpoint@1 {
				reg = <1>;
				remote-endpoint = <&ucam_out1>;
				data-lanes = <1 2>;
			};
		};

		port@1 {
			reg = <1>;
			#address-cells = <1>;
			#size-cells = <0>;

			dphy_tx1rx1_out: endpoint@0 {
				reg = <0>;
				remote-endpoint = <&isp1_mipi_in>;
			};
		};
	};
};

&rkisp1_1 {
	status = "okay";

	port {
		#address-cells = <1>;
		#size-cells = <0>;

		isp1_mipi_in: endpoint@0 {
			reg = <0>;
			remote-endpoint = <&dphy_tx1rx1_out>;
		};
	};
};

/home/m/edge/device/rockchip/rk3399/rk3399_Android10/rk3399_Android10.mk

PRODUCT_PROPERTY_OVERRIDES += \
	persist.sys.rotation.efull=true \
	persist.vendor.sys.hdmiui=2 \
	persist.sys.rotation.einit=3 \
	persist.sys.app.rotation=force_land \
	sys.magisk.adb.root=1 \
	vendor.hwc.device.primary=eDP,DP\
	vendor.hwc.device.extend=HDMI-A

monkey_m4 · July 24, 2022, 8:25am

屏参数

goenjoy · July 25, 2022, 1:51am

uboot显示正常不？若正常这里修改persist.sys.rotation.einit=0试试。

monkey_m4 · July 25, 2022, 4:52am

uboot logo没显示 android 那个动图显示也是不正常的

goenjoy · July 25, 2022, 6:21am

@monkey_m4 建议把hdmi, dp有关显示节点都disabled看看。即只配置一个edp屏，且挂载在vopb上。

goenjoy · July 25, 2022, 6:42am

另外dts的hdmi你并没有配置在vopl上。你也可以这个修改试试，hdmi作为副屏且挂载在vopl上(V PLL也要跟着hdmi变化)：

&hdmi_in_vopb {
	status = "disabled";
};

&hdmi_in_vopl {
	status = "okay";
};

&route_hdmi {
	status = "okay";
	connect = <&vopl_out_hdmi>;
};

&vopb {
	status = "okay";
	assigned-clocks = <&cru DCLK_VOP0_DIV>;
	assigned-clock-parents = <&cru PLL_CPLL>;
};

&vopl {
	status = "okay";
	assigned-clocks = <&cru DCLK_VOP1_DIV>;
	assigned-clock-parents = <&cru PLL_VPLL>;
};

@monkey_m4

monkey_m4 · July 25, 2022, 1:52pm

好的谢谢我再试试现在源码又不能编译了卡在make installclean 这步