Edge跑常温老化测试失败,打印log乱码

您好!我们用Edge在常温下播放高清视频进行老化测试,24小时内就会自动重启或卡死无反应必须重新上电;跑“激流勇进”3D游戏常温下10分钟左右就会重启。我们接串口打印抓取log,正常情况下也都是乱码,确定使用的串口工具和软件都设置无误(在我们买的VIM2/VIM3上都工作正常,串口设置如下图),请帮忙解决以上问题,谢谢!

@lwind 波特率是1500000 ,不是115200

谢谢!波特率设置1500000后打印乱码问题解决。
然后常温下跑了一下3D游戏,这个游戏是启动以后不用操作就会处于游艇演示循环,一个循坏大概一分钟,刚才正好抓了一下一个循环就重启的log,请帮忙解决一下是什么问题导致的重启,谢谢!
以下是抓取的log,在分割线以上为系统正常启动且开启3D游戏时的log,分割线以下为系统重启时及以后的log。

[   17.129118] dhd_conf_read_config: Ignore config file /system/etc/firmware/config.txt
[   17.129162] Final fw_path=/system/etc/firmware/fw_bcm4359c0_ag.bin
[   17.129168] Final nv_path=/system/etc/firmware/nvram_ap6398sr3.txt
[   17.129174] Final clm_path=/system/etc/firmware/clm_bcmdhd.blob
[   17.129179] Final conf_path=/system/etc/firmware/config.txt
[   17.129186] dhd_set_bus_params: set use_rxchain 0
[   17.129193] dhd_set_bus_params: set txinrx_thres 128
[   17.129198] dhd_set_bus_params: set txglomsize 36
[   17.130302] dhd_os_open_image: /system/etc/firmware/fw_bcm4359c0_ag.bin (594889 bytes) open success
[   17.204750] dhd_os_open_image: /system/etc/firmware/nvram_ap6398sr3.txt (5802 bytes) open success
[   17.205255] NVRAM version: AP6398SR3_NVRAM_V1.0_20171106.txt

[   17.206122] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[   17.369956] init: cannot find '/system/bin/glgps' (No such file or directory), disabling 'gpsd'
[   17.371084] init: Starting service 'exec 6 (/system/bin/bootstat)'...
[   17.378857] type=1400 audit(1358499087.256:29): avc: denied { write } for pid=1 comm="init" name="su" dev="dm-0" ino=1474564 scontext=u:r:init:s0 tcontext=u:object_r:system_file:s0 tclass=file permissive=1
[   17.385469] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[   17.385890] si_get_pmu_reg_addr: addrRET: 18000670
[   17.386213] bcmsdh_oob_intr_register HW_OOB irq=75 flags=0x4
[   17.387677] Disable tdls_auto_op failed. -1
[   17.387714] dhd_preinit_ioctls: Set tcpack_sup_mode 1
[   17.388321] dhd_apply_default_clm: Ignore clm file /system/etc/firmware/clm_bcmdhd.blob
[   17.395202] Firmware up: op_mode=0x0405, MAC=28:ed:e0:e6:9a:ce
[   17.395240] dhd_conf_set_country: set country CN, revision 38
[   17.406575] init: Service 'exec 6 (/system/bin/bootstat)' (pid 1101) exited with status 0
[   17.406883] init: Starting service 'exec 7 (/system/bin/bootstat)'...
[   17.411793] dhd_wlfc_enable: ret=0
[   17.411843] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
[   17.411860] CFG80211-ERROR) wl_cfg80211_event : Event handler is not created
[   17.412616] Country code: CN (CN/38)
[   17.413025] dhd_conf_set_intiovar: set roam_off 1
[   17.415229] dhd_conf_set_intiovar: set txbf 1
[   17.415507] CONFIG-ERROR) dhd_conf_set_intiovar: txbf setting failed -23
[   17.416386] dhd_conf_set_intiovar: set WLC_SET_FAKEFRAG 219 1
[   17.421925]   Driver: 1.579.77.41.2 (r)
[   17.421925]   Firmware: wl0: Nov  1 2017 10:40:09 version 9.87.51.11.5 (2334dcf@sh-git) (r) FWID 01-f9f1e123
[   17.421925]   CLM: 9.7.5 
[   17.422214] dhd_txglom_enable: enable 1
[   17.422235] dhd_conf_set_txglom_params: txglomsize=36, deferred_tx_len=36, bus_txglom=-1
[   17.422242] dhd_conf_set_txglom_params: tx_in_rx=1, txinrx_thres=128, dhd_txminmax=-1
[   17.422249] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=5
[   17.422257] sdioh_set_mode: set txglom_mode to copy
[   17.422287] dhd_conf_get_disable_proptx: fw_proptx=1, disable_proptx=-1
[   17.427753] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
[   17.428009] dhd_conf_set_intiovar: set ampdu_hostreorder 1
[   17.428770] dhd_pno_init: Support Android Location Service
[   17.428784] dhd_preinit_ioctls: SensorHub diabled 0
[   17.429017] dhd_preinit_ioctls failed to set ShubHub disable
[   17.429021] init: Service 'exec 7 (/system/bin/bootstat)' (pid 1109) exited with status 0
[   17.429393] init: Starting service 'exec 8 (/system/bin/bootstat)'...
[   17.429802] failed to set WNM capabilities
[   17.429834] wl_android_wifi_on: Success
[   17.447528] init: Service 'exec 8 (/system/bin/bootstat)' (pid 1110) exited with status 0
[   17.448448] init: Starting service 'exec 9 (/system/bin/bootstat)'...
[   17.454770] dhd_wlfc_enable: ret=0
[   17.468338] init: Service 'exec 9 (/system/bin/bootstat)' (pid 1113) exited with status 0
[   17.471302] dhd_open: Exit ret=0
[   17.485773] init: Starting service 'p2p_supplicant'...
[   17.586632] P2P interface registered
[   17.586671] wl_cfgp2p_add_p2p_disc_if: wdev: ffffffc0e4f9c200, wdev->net:           (null)
[   17.592313] WLC_E_IF: NO_IF set, event Ignored

[   17.594262] P2P interface started
[   17.652814] Random MAC OUI to be used - da:a1:19
[   17.660114] net_os_enable_packet_filter: val = 0
[   17.661307] net_os_rxfilter_add_remove: add_remove = 0, num = 2
[   17.668770] net_os_enable_packet_filter: val = 1
[   17.669612] net_os_enable_packet_filter: val = 0
[   17.670182] net_os_rxfilter_add_remove: add_remove = 0, num = 3
[   17.671689] net_os_enable_packet_filter: val = 1
[   17.683185] dhd_set_suspend: Remove extra suspend setting 
[   17.683210] dhd_enable_packet_filter: enter, value = 0
[   18.585389] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[   18.610630] sdcardfs version 2.0
[   18.610667] sdcardfs: dev_name -> /mnt/media_rw/0526-11B3
[   18.610676] sdcardfs: options -> fsuid=1023,fsgid=1023,mask=6,userid=0,gid=1015
[   18.610686] sdcardfs: mnt -> ffffffc0ccf67de0
[   18.610791] sdcardfs: mounted on top of /mnt/media_rw/0526-11B3 type vfat
[   18.614703] sdcardfs version 2.0
[   18.614769] sdcardfs: dev_name -> /mnt/media_rw/0526-11B3
[   18.614776] sdcardfs: options -> fsuid=1023,fsgid=1023,mask=18,userid=0,gid=9997
[   18.614784] sdcardfs: mnt -> ffffffc0cb48ce20
[   18.614835] sdcardfs: mounted on top of /mnt/media_rw/0526-11B3 type vfat
[   18.617266] sdcardfs version 2.0
[   18.617286] sdcardfs: dev_name -> /mnt/media_rw/0526-11B3
[   18.617292] sdcardfs: options -> fsuid=1023,fsgid=1023,mask=18,userid=0,gid=9997
[   18.617299] sdcardfs: mnt -> ffffffc0c8c943a0
[   18.617334] sdcardfs: mounted on top of /mnt/media_rw/0526-11B3 type vfat
[   20.792092] init: Service 'bootanim' is being killed...
[   20.808830] sensors 7-0068: set sensor poll time to 20ms
[   20.835094] init: Service 'bootanim' (pid 285) killed by signal 9
[   20.886064] sensors 7-0068: sensor on: starting poll sensor data 18ms
[   44.193709] init: avc:  denied  { set } for property=sys.launcher.state pid=1289 uid=10045 gid=10045 scontext=u:r:untrusted_app:s0:c512,c768 tcontext=u:object_r:system_prop:s0 tclass=property_service permissive=1
[   44.203245] type=1400 audit(1358499114.076:30): avc: denied { write } for pid=1289 comm="droid.launcher3" name="property_service" dev="tmpfs" ino=2196 scontext=u:r:untrusted_app:s0:c512,c768 tcontext=u:object_r:property_socket:s0 tclass=sock_file permissive=1
[   44.203519] type=1400 audit(1358499114.076:31): avc: denied { connectto } for pid=1289 comm="droid.launcher3" path="/dev/socket/property_service" scontext=u:r:untrusted_app:s0:c512,c768 tcontext=u:r:init:s0 tclass=unix_stream_socket permissive=1
[   49.563841] sensors 7-0068: set sensor poll time to 20ms
[   49.564385] sensors 7-0068: set sensor poll time to 16ms

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

[  116.108863] usb 7-1: USB disconnect, device number 2
[  116.108922] usb 7-1.2: USB disconnect, device number 3
[  116.181251] usb 7-1.4: USB disconnect, device number 4
[  116.202270] type=1400 audit(1358499186.086:32): avc: denied { read } for pid=216 comm="vold" name="fd" dev="proc" ino=2339 scontext=u:r:vold:s0 tcontext=u:r:logd:s0 tclass=dir permissive=1
[  116.202522] type=1400 audit(1358499186.086:33): avc: denied { open } for pid=216 comm="vold" path="/proc/205/fd" dev="proc" ino=2339 scontext=u:r:vold:s0 tcontext=u:r:logd:s0 tclass=dir permissive=1
[  116.202637] type=1400 audit(1358499186.086:34): avc: denied { getattr } for pid=216 comm="vold" path="/proc/205/fd/0" dev="proc" ino=39125 scontext=u:r:vold:s0 tcontext=u:r:logd:s0 tclass=lnk_file permissive=1
[  116.203753] type=1400 audit(1358499186.086:35): avc: denied { read } for pid=216 comm="vold" name="0" dev="proc" ino=39125 scontext=u:r:vold:s0 tcontext=u:r:logd:s0 tclass=lnk_file permissive=1
  DDR Version 1.19 20190305
In
channel 0
CS = 0
MR0=0x19
MR4=0x3
MR5=0x6
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
CS = 1
MR0=0x19
MR4=0x3
MR5=0x6
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 1
CS = 0
MR0=0xB8
MR4=0x2
MR5=0x13
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 0 training pass!
channel 1 training pass!
change freq to 400MHz 0,1
channel 0
CS = 0
MR0=0x19
MR4=0x3
MR5=0x6
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
CS = 1
MR0=0x19
MR4=0x3
MR5=0x6
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 1
CS = 0
MR0=0xB8
MR4=0x2
MR5=0x13
MR8=0x10
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 0 training pass!
channel 1 training pass!
change freq to 800MHz 1,0
Channel 0: LPDDR4,800MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
Channel 1: LPDDR4,800MHz
Bus Width=32 Col=10 Bank=8 Row=16 CS=1 Die Bus-Width=16 Size=2048MB
256B stride
ch 0 ddrconfig = 0x101, ddrsize = 0x2020
ch 1 ddrconfig = 0x101, ddrsize = 0x40
pmugrf_os_reg[2] = 0x32C1FAA1, stride = 0xD
OUT
Boot1: 2019-01-17, version: 1.18

@lwind 这个安卓系统的log,我的同事 @goenjoy 会协助你


这里的LOG去哪里啦?你的机器有没有作散热处理?否则会因为过热很容易导致机器重启。

一行“@”是我做的分隔符,原始log里这里上下是连续的。我们外部加了一个风扇在吹,没有加原装散热器,我们在VIM2/VIM3上也是这样做到,这两款就没有问题,这是不是说RK的芯片发热大,必须更强力散热才行?如果这样我们高温老化试验就更没办法做了

那你要把完整的LOG发出来啊。。

拍个照片看看,风扇吹的话,要对准CPU吹才有效果。

我就是加了一个USB接口的小风扇对着主控吹风。视频播放时间在数小时后才会有重启现象,3D游戏多次是在几分钟内就会重启。那RK3399这个主控在温度达到多少度以后会重启?你们是否设置有这个限值

115度。把LOG发出来,3D游戏apk也发出来