Which system do you use? Android, Ubuntu, OOWOW or others?
Ubuntu
Which version of system do you use? Please provide the version of the system here:
I tried Khadas Official Images:
vim4-ubuntu-22.04-gnome-linux-5.4-fenix-1.5-230425.img.xz
vim4-ubuntu-22.04-gnome-linux-5.15-fenix-1.7.1-240930.img.xz
Please describe your issue below:
2 new VIM4 devices after the first firmware of the OS fell into an endless reloading cycle.
In the loading log, the problem is in the following place:
Hit SPACE in 2 seconds to stop autoboot
starting USB...
USB0: Register 1000120 NbrPorts 1
Starting the controller
USB XHCI 1.10
USB1: No ----gpio-vbus-power
Register 2000120 NbrPorts 1
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... XHCI timeout on event type 33... cannot recover.
BUG at ../drivers/usb/host/xhci-ring.c:474/xhci_wait_for_event()!
BUG!
resetting ...
Normal loading looks like this:
Hit SPACE in 2 seconds to stop autoboot
starting USB...
USB0: Register 1000120 NbrPorts 1
Starting the controller
USB XHCI 1.10
USB1: No ----gpio-vbus-power
Register 2000120 NbrPorts 1
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 3 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Both devices sometimes load and work normally until the next reboot. Oowow updated to the latest version.
At the moment, I have 30 devices in my hands from which 2 behave inappropriately.
Post a console log of your issue below:
Board ID = 6
Set sys clock to 24Mhz
syspll is 1512Mhz. Locked
sys1pll is 1608Mhz. Locked
Set sys clock to 167Mhz
gp0pll is 0Mhz. Locked
bl2_platform_setup
boot area list:
1STBLOB 00000200 00040000
BL2E 00040200 00013000
BL2X 00053200 00011000
DDRFIP 00064200 00040000
DEVFIP 000a4200 00300000
s_setup from rom:00010081
dma mode
derive RSPK OK
DDR driver_vesion: AML_S_PHY_T7_1_18 build time: Sep 13 2022 15:55:10
ddr id: 0
ddr clk to 2016MHz
ch0 clk 2016
ch1 clk 2016PIEI done
Cfg max: 2, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe
ddr clk to 2016MHz
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
ch0 1D training succeed
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
ch1 1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : Training has run successfully!
R0_Rx=9 steps R0_Tx=10 steps Vref_Margin_R0=19 Dramvref_Margin_R0=20
R0_Rx=11 steps R0_Tx=11 steps Vref_Margin_R0=19 Dramvref_Margin_R0=20
soc_vref_reg_value 0x 00000021 00000022 00000020 00000021 00000021 00000021 00000022 00000022 00000022 00000021 00000022 00000022 0000001f 00000020 00000020 00000021 00000021 00000021 00000021 00000020 00000020 00000021 00000021 00000020 00000022 00000022 00000021 00000022 00000021 00000021 00000021 00000020
mr8=00000011
dram_verdor_id=00000006
mr18=000000c1
mr19=00000004 dram_vref_reg_value 0x 00000008
ch0 2D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : Training has run successfully!
R0_Rx=9 steps R0_Tx=10 steps Vref_Margin_R0=17 Dramvref_Margin_R0=19
R0_Rx=11 steps R0_Tx=11 steps Vref_Margin_R0=20 Dramvref_Margin_R0=20
soc_vref_reg_value 0x 00000020 00000021 00000021 00000021 00000021 00000020 00000021 00000022 00000021 0000001f 00000020 00000021 00000021 00000020 00000022 00000021 00000020 00000020 00000020 00000020 00000021 00000021 00000020 00000021 00000020 00000020 00000021 0000001f 00000021 00000021 00000020 00000020
mr8=00000011
dram_verdor_id=00000006
mr18=000000c2
mr19=00000004 dram_vref_reg_value 0x 00000008
ch1 2D training succeed
100bdlr_step_size ps== 442
100bdlr_step_size ps== 450
finnal_config_axi
finnal_config_axiset_cci_config:
cpu0_gic_init done
start ao cpu:
Wait AO...done.
debug_read..
SYSCTRL_CCI_CFG1==ffff3fff
SYSCTRL_CCI_CFG9==aaaaaaaa
SYSCTRL_NOC_CFG0==00000000
dram_size_config==10001000ap ao cmd ok
DDR cs0 size: 2048MB
DDR cs1 size: 2048MB
DMC_DDR_CTRL: 00e00044DDR size: 3584MB
DDR cs0 size: 2048MB
DDR cs1 size: 2048MB
DMC_DDR_CTRL: 00e00044DDR size: 3584MB
result report
non-sec scramble use random key
scramble use random key
ddr scramble enabled
INFO: bl2_load_bl2ex start!
INFO: load ...
Load: BL2E From: eMMC - 3.0 src: 00002000, dst: 00fffff0, size: 00011000
sdemmc src: ;
INFO: check ...
SHA CHK OK!
aml log : dump from buffer 01000000
56 d9 25 42 e3 66 20 59 34 60 7c ab a7 53 de 08
78 8e 84 3a 8a 98 b7 26 a1 bf 63 5d 79 44 1f 75
INFO: load ...
Load: BL2X From: eMMC - 3.0 src: 00000000, dst: 007ffff0, size: 00011000
sdemmc src: ;
INFO: check ...
SHA CHK OK!
aml log : dump from buffer 00800000
dc 2c fc e6 5b fd 25 3a a5 0c c2 b2 3f 72 cc c8
0b a3 b5 b9 cf 47 49 f5 e3 28 8c a5 84 ac 9d 1d
run into bl2e
info: get valid params from BL2 !
BL2E: do things as vendor specific ...
Hello world, now in BL2E
TE: 1101899
BL2E Built : 12:23:58, Sep 9 2022. t7 origin/master g0a0ad46 - jenkins@walle02-sh
Start to do bl2e platform setup !
boot area list:
1STBLOB 00000200 00040000
BL2E 00040200 00013000
BL2X 00053200 00011000
DDRFIP 00064200 00040000
DEVFIP 000a4200 00300000
eMMC boot @ 0
sw-hs2 s
tun-w: s=0, sz=3
sw8 s
aml log : BL2E load BL3X.....
TE: 1107098
Load FIP HDR from eMMC, src: 0x00000000, des: 0x00300000, size: 0x00008000, part: 0
Load BL3X from eMMC, src: 0x00008000, des: 0x00308000, size: 0x0026c260, part: 0
bl30 payload size: 0x00010260
bl30 memcpy
bl40 payload size: 0x00018470
bl31 payload size: 0x00040470
bl32 payload size: 0x00080470
bl33 memcpy
bl33 payload size: 0x00180260 offset: 0x000f4000
aml log : BL2E loading BL3X is done...!
boot bl2x
params to bl2x, address=0x0100d190
Hello, we are in BL2X world !
TE: 1161514
BL2X Built : 19:48:00, Aug 18 2022. t7 origin/master g161cca2 - jenkins@walle02-sh
bl2_platform_setup
INFO: get valid list_blobinfo, 0x0100d190
Info: get valid bl31 payload info, address= 0x00332000 size= 0x00040470
Info: bl31 image is now ready !
Info: get valid bl40 payload info, address= 0x00319000 size= 0x00018470
FEAT_DISABLE_SECURE_ENCLAVE: 1
bl2e_2 entry: 010000c0
run into bl31
NOTICE: BL31: v1.3(release):82fe3e48d
NOTICE: BL31: Built : 10:34:03, Nov 4 2022. t7 remotes/firmware/amlogic-dev-1.3 g82fe3e48d - jenkins@walle02-sh
BL31:tsensor calibration: tsensor1 = 960000ab
BL31:tsensor calibration: tsensor2 = 960000da
BL31:tsensor calibration: tsensor3 = 960000d7
BL31:tsensor calibration: tsensor4 = 960000ab
BL31:tsensor calibration: tsensor5 = 960000cf
BL31:tsensor calibration: tsensor6 = 960000a7
[mhu]: mhu_init-v1
[mhu]: 0xfe007100, 0x12120210
[mhu]: 0xfe007104, 0x12121002
[mhu]: 0xfe00710c, 0xa0a0802
[mhu]: 0xfe007118, 0x12120210
[mhu]: 0xfe00711c, 0x12121002
[mhu]: 0xfe007120, 0x10101010
[mhu]: 0xfe007124, 0x10101010
[mhu]: 0xfe007020, 0x3
[mhu]: 0xfe007028, 0x10
[mhu]: 0xfe007024, 0x8
[mhu]: 0xfe00702c, 0x10
[mhu]: 0xfe007040, 0x9089
[mhu]: 0xfe007044, 0x0
[mhu]: 0xfe007048, 0x660
[mhu]: 0xfe00704c, 0x0
[mhu]: 0xfe007050, 0x90006
[mhu]: 0xfe007054, 0x0
[mhu]: 0xfe007058, 0x66000
[mhu]: 0xfe00705c, 0x0
[mhu]: mhu_init-v1 1230 done
DEVICE_MVN=0x0
NOTICE: BL31: T7 normal boot!
NOTICE: BL31: BL33 decompress pass
E/TC:0 00 INFO: BL3-2: ATOS-V3.8.0-ff9afab78 (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #1 Mon 31 Oct 2022 06:56:43 AM UTC arm
E/TC:0 00 INFO: BL3-2: secure time TEE
E/TC:0 00 INFO: BL3-2: Chip: T7 Rev: B (36:B - 0:3)
Hello world again, bl2e meet you guys!
valid entry info for bl33, pc = 0x00000000
======== smc start aocpu ========
Starting AOCPU FreeRTOS...
AOCPU image version='khadas-vims-v2019.01 b9765fa800452361aa7b346ac7c3f8e88de77d8e 11:45:25 2023-04-25'
AOCPU_IRQ_SEL=0x0
AOCPU_IRQ_SEL=0x0
AOCPU_IRQ_SEL=0x0
AOCPU_IRQ_SEL=0x0
[AOCPU]: mailbox init start
reg idx=0 cmd=6 handler=f7026a0c
reg idx=1 cmd=7 handler=f70269f6
[AOCPU]: mailbox init end
[AOCPU Led]: leds state init!
reg idx=2 cmd=f7 handler=f702181e
[AOCPU Led]: Starting leds task ...
Starting timer ...
reg idx=3 cmd=b4 handler=f702360a
reg idx=4 cmd=b5 handler=f70235a2
reg idx=5 cmd=b6 handler=f70230ce
reg idx=6 cmd=bb handler=f702308e
reg idx=7 cmd=bc handler=f70230ae
reg idx=8 cmd=11 handler=f7027676
reg idx=9 cmd=12 handler=f7027698
reg idx=10 cmd=35 handler=f70278e4
reg idx=11 cmd=4 handler=f7021ece
reg idx=12 cmd=30 handler=f7021e98
reg idx=13 cmd=31 handler=f7021ea8
reg idx=14 cmd=40 handler=f7021eac
reg idx=15 cmd=f9 handler=f7021f58
Starting task scheduler ...
boot bl33 !
env_init: Environment nowhere init done (ret=0)
U-Boot 2019.01 (Apr 25 2023 - 11:45:18 +0000)
DRAM: 8 GiB
Relocation Offset is: df5c2000
Relocating to df5c2000, new gd at d95b1dc8, sp at d95b1db0
board init
watchdog disable
gpio: pin GPIOT_15 (gpio 106) value is 1
fusb302_init: Device ID: 0x91
CC connected in 0 as UFP
fusb302 detect chip.port_num = 0
gpio: pin GPIOH_4 (gpio 152) value is 1
gpio: pin GPIOT_15 (gpio 106) value is 0
gpio: pin GPIOH_3 (gpio 151) value is 0
Setting bus to 6
[meson_mmc_probe]sd: Controller probe success!
[meson_mmc_probe]emmc: Controller probe success!
emmc: resp timeout, cmd8, status=0x1cf2800
emmc: resp timeout, cmd55, status=0x1cf2800
store flag: 0, types: 1
emmc init success!
boot_device:1
boot_seq:0
boot_bakups:3
rebuild_id :0
boot area list:
bl2 200 40000
bl2e 40200 13000
bl2x 53200 11000
ddrfip 64200 40000
devfip a4200 300000
emmc: tuning start:
emmc: best_win_start =5, best_win_size =5
emmc: clk = 10000206, dly1 = 0, dly2 = 0, adj = 12000, cfg = 804872
fill_ept_by_gpt: invalid gpt
get_partition_from_dts() 232: ret 0
parts: 1
00: rootfs ffffffffffffffff 4
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
emmc probe success
In: serial@8000
Out: serial@8000
Err: serial@8000
board common misc_init
board late init
upgrade_step 0
the dtb partition size is:40000 byte
_verify_dtb_checksum()-2947: calc 7b52bc62, store 7b52bc62
_verify_dtb_checksum()-2947: calc 7b52bc62, store 7b52bc62
dtb_read()-3162: total valid 2
update_old_dtb()-3143: do nothing
vpu: find AML_VPU_CLK_LEVEL_DFT: 7
vpu: clk_level in dts: 7
vpu: vpu_power_on_new
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: vpu_module_init_config
vpu: vpu_probe
limit_res_1080p: 0
enc_idx: 2
vpp: vpp_init, chip_id=54
vpp: set_osd1_rgb2yuv rgb2yuv on = 0..............
vpp: set_osd2_rgb2yuv rgb2yuv on = 0..............
vpp: set_osd3_rgb2yuv rgb2yuv on = 0..............
vpp: T7 osd4 matrix rgb2yuv..............
hdr_func: 0x8, hdr_process_select 0x20000001
hdr_func: hdr_process_select = 536870913
hdr_func: 0x100, hdr_process_select 0x20000001
hdr_func: hdr_process_select = 536870913
hdr_func: 0x200, hdr_process_select 0x20000001
hdr_func: 0x1, hdr_process_select 0x1
hdr_func: 0x2, hdr_process_select 0x1
rx trim:0x1
mipi_lcd_exist : 0
lcd: lcd_debug_print flag: 0
lcd: [0]: detect mode: tablet, key_valid: 0, clk_path: 0
lcd: config load from dts
lcd: [0]: use panel_type=mipi_0
lcd: load dts config: TS050, lcd_type: mipi(3)
lcd: [0]: TS050, mipi, 8bit, 1080x1920
lcd: [1]: detect mode: tablet, key_valid: 0, clk_path: 0
lcd: config load from dts
lcd: [1]: use panel1_type=vbyone_1
lcd: load dts config: public_1region, lcd_type: vbyone(2)
lcd: [1]: lcd_clk is 0, default to 60Hz
lcd: [1]: public_1region, vbyone, 10bit, 3840x2160
lcd: [2]: detect mode: tablet, key_valid: 0, clk_path: 0
lcd: config load from dts
lcd: [2]: use panel2_type=lvds_1
lcd: load dts config: 1080p-hfreq_hdmi, lcd_type: lvds(1)
lcd: [2]: lcd_clk is 0, default to 60Hz
lcd: [2]: 1080p-hfreq_hdmi, lvds, 8bit, 1920x1080
bl: find en_sequence_reverse: 0
bl: [0]: name: backlight_pwm, method: 1
buff: 9056201e4331180a
Net: pwr up eth
ex-phy
chip num 3
set rgmii
Setting bus to 6
[KM]Msg:key_num: 22
[KM]Msg:normal key used!
the key partition size is:40000 byte
calc 0, store 0
cpy 1 is not valid
calc 0, store 0
cpy 0 is not valid
[KM]Msg:mark is not found
[EFUSE_MSG]keynum is 4
MACADDR:02:ad:36:01:ea:b5(from sec_reg)
eth0: ethernet@fdc00000
recovery_status=
upgrade_step=0
check_display reboot_mode : ,powermode : on
do_hpd_detect, hpd_state=1
vout_hdmi_hpd: lcd no need hpd detect
vout_hdmi_hpd: hdmimode=1080p60hz
vout_hdmi_hpd: colorattribute=444,8bit
set outputmode: hdmimode=1080p60hz
Dump EDID Rawdata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_montorcapable861: ycbcr444=1, ycbcr422=1
HDMI_EDID_BLOCK_TYPE_VENDER: prxcap->ColorDeepSupport=0x0
sink preferred_mode is <NULL>[0]
hdr mode is 0
dv mode is ver:0 len: 0
hdr10+ mode is 0
Dump EDID Rawdata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_montorcapable861: ycbcr444=1, ycbcr422=1
HDMI_EDID_BLOCK_TYPE_VENDER: prxcap->ColorDeepSupport=0x0
read hdmichecksum: 0x00000000, hdmimode: 1080p60hz, colorattribute: 444,8bit
TV has changed, initial mode: 1080p60hz attr: 444,8bit now crc: 0x60840000
ubootenv dv_type: 0, hdr_priority: 0
ubootenv best_output: 1, framerate_priority: 1
the resolveResolution mode [2560x1080p50hz] is not valid
the resolveResolution mode [2560x1080p60hz] is not valid
the resolveResolution mode [640x480p60hz] is not valid
the resolveResolution mode [800x480p60hz] is not valid
the resolveResolution mode [852x480p60hz] is not valid
the resolveResolution mode [854x480p60hz] is not valid
the resolveResolution mode [3840x1080p60hz] is not valid
set HDMI to highest edid mode: 1080p60hz
support current mode:[1080p60hz], deep color:[444,8bit]
colorattribute = 444,8bit
sdr final_displaymode:1080p60hz, final_deepcolor:444,8bit
update hdmimode: 1080p60hz
update colorattribute: 444,8bit
update hdmichecksum: 0x60840000
Manufacturer: AOC Model 2402 Serial Number 1336
EDID version: 1.3
Established timings supported:
720x400@70Hz
640x480@60Hz
640x480@67Hz
640x480@72Hz
640x480@75Hz
800x600@56Hz
800x600@60Hz
800x600@72Hz
800x600@75Hz
832x624@75Hz
1024x768@60Hz
1024x768@70Hz
1024x768@75Hz
1280x1024@75Hz
Standard timings supported:
1920x1080@60Hz
1680x1050@60Hz
1440x900@60Hz
1280x1024@60Hz
1280x960@60Hz
1280x720@60Hz
Detailed mode (1) : Clock 148 MHz, 527 mm x 296 mm
1920 2008 2052 2200 hborder 0
1080 1084 1089 1125 vborder 0
+hsync +vsync
Detailed mode (1) : Clock 174 MHz, 527 mm x 296 mm
1920 1968 2000 2080 hborder 0
1080 1083 1088 1119 vborder 0
+hsync -vsync
Monitor name: 24V2W1G5
Monitor ranges (GTF): 48-76Hz V, 30-85kHz H, max dotclock 180MHz
Has 1 extension blocks
Checksum: 0x60 (valid)
khadas_support_mode 1080p60hz
bestmode is 1080p60hz, IEEEOUI 0x000000
HDMI Mode
dolby_vision_process: hpd_state=1
dolby_status 0 1
dolby_vision_process: hpd: dv disabled
Unknown command 'saveenv' - try 'help'
do_hpd_detect, hpd_state=1
vout_hdmi_hpd: lcd no need hpd detect
vout_hdmi_hpd: hdmimode=1080p60hz
vout_hdmi_hpd: colorattribute=444,8bit
set outputmode: hdmimode=1080p60hz
osd: hpd_state=1
[OSD]load fb addr from dts:/fb
[OSD]status disabled
[OSD]load fb addr from dts:/drm-vpu
[OSD]set initrd_high: 0x3f800000
[OSD]fb_addr for logo: 0x3f800000
[OSD]load fb addr from dts:/fb
[OSD]status disabled
[OSD]load fb addr from dts:/drm-vpu
[OSD]fb_addr for logo: 0x3f800000
MMC: no card present
mmc_init: -123, time 0
MMC: no card present
mmc_init: -123, time 0
fs_devread read outside partition 2
Failed to mount ext2 filesystem...
btrfs_read_superblock: No valid BTRFS superblock found!
** Unrecognized filesystem type **
1080138 bytes read in 11 ms (93.6 MiB/s)
[OSD]axis(0, 0, 1920, 1080)
[OSD]osd_hw.free_scale_data: 0, 1919, 0, 1079
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]vmode = 15, pi_enable = 0
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
is_osd2_configed ret=0
set hdmitx VIC = 16 CS = 2 CD = 4
aml_audio_init
configure venc
configure VIC16 timing
hdmitx_check_frac_rate: frac_rate:1
config HPLL = 5940000 frac_rate = 1
clocks_set_vid_clk_div_for_hdmi[526] div = 6
configure hdmitx21
div40: 0
hdmi_tx_set: save mode: 1080p60hz, attr: 444,8bit, hdmichecksum: 0x60840000
[OSD]axis(0, 0, 1920, 1080)
[OSD]osd_hw.free_scale_data: 0, 1919, 0, 1079
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]vmode = 15, pi_enable = 0
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
is_osd2_configed ret=0
[OSD]load fb addr from dts:/fb
[OSD]status disabled
[OSD]load fb addr from dts:/drm-vpu
[OSD]fb_addr for logo: 0x3f800000
[OSD]load fb addr from dts:/fb
[OSD]status disabled
[OSD]load fb addr from dts:/drm-vpu
[OSD]fb_addr for logo: 0x3f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
dolby_status 0 1
MMC: no card present
mmc_init: -123, time 0
MMC: no card present
mmc_init: -123, time 0
fs_devread read outside partition 2
Failed to mount ext2 filesystem...
btrfs_read_superblock: No valid BTRFS superblock found!
** Unrecognized filesystem type **
1080138 bytes read in 11 ms (93.6 MiB/s)
[OSD]axis(0, 0, 1920, 1080)
[OSD]osd_hw.free_scale_data: 0, 1919, 0, 1079
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]vmode = 15, pi_enable = 0
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]osd0_update_disp_freescale_enable
is_osd2_configed ret=0
[OSD]osd_hw.free_scale_data: 0, 1919, 0, 1079
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]vmode = 15, pi_enable = 0
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]osd1_update_disp_freescale_enable
[OSD]axis(0, 0, 1920, 1080)
[OSD]osd_hw.free_scale_data: 0, 1919, 0, 1079
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]vmode = 15, pi_enable = 0
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]osd0_update_disp_freescale_enable
is_osd2_configed ret=1
set hdmitx VIC = 16 CS = 2 CD = 4
aml_audio_init
configure venc
configure VIC16 timing
hdmitx_check_frac_rate: frac_rate:1
config HPLL = 5940000 frac_rate = 1
clocks_set_vid_clk_div_for_hdmi[526] div = 6
configure hdmitx21
div40: 0
hdmi_tx_set: save mode: 1080p60hz, attr: 444,8bit, hdmichecksum: 0x60840000
dolby_status 0 1
dolby_status 0 1
hdr_packet
vpp: hdr_policy = 0
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
s_version: 01.01.230425.114518
s_version: 01.01.230425.114518
[KM]Msg:key_num: 22
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L401:key[region_code] not programed yet
[KM]Error:f[key_manage_query_size]L401:key[deviceid] not programed yet
Setting bus to 6
usid=2cb0000333
usid=2cb0000333
Setting bus to 6
mac=c8:63:14:73:45:7e
Setting bus to 6
normal power on
Setting bus to 6
boot wol: disable
Setting bus to 6
gpio: pin GPIOD_4 (gpio 61) value is 1
reboot_mode : cold_boot
cold boot: ffv_wake=off powermode=on suspend=off
Hit SPACE in 2 seconds to stop autoboot
starting USB...
USB0: Register 1000120 NbrPorts 1
Starting the controller
USB XHCI 1.10
USB1: No ----gpio-vbus-power
Register 2000120 NbrPorts 1
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... XHCI timeout on event type 33... cannot recover.
BUG at ../drivers/usb/host/xhci-ring.c:474/xhci_wait_for_event()!
BUG!
resetting ...