Which system do you use? Android, Ubuntu, OOWOW or others?
Others - manjaro linux
Which version of system do you use? Please provide the version of the system here:
Please describe your issue below:
I can not access upgrade mode: tested all method from:
By M-register mode while I shourtcut the MRegiser pad serial console show:
GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:800;NAND:81;SD:800;USB:8;LOOP:1;EMMC:800;NAND:81;SD:800;USB;
I can still access u-boot (think is not khadas original) and boot from emmc (manjaro linux) or sdcard
Post a console log of your issue below:
**GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:800;NAND:81;SD:800;USB:8;LOOP:1;EMMC:800;NAND:81;SD:800;USB;**
TE: 40236916
BL2 Built : 14:59:36, Aug 9 2017.
gxl ge8c6a83 - xiaobo.gu@droid12
set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - FAIL
DDR4 chl: Rank0+1 @ 1008MHz - PASS
Rank0: 2048MB(auto)-2T-18
Rank1: 1024MB(auto)-2T-18
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x0002c600
Load bl33 from eMMC, src: 0x00050200, des: 0x01000000, size: 0x000b7600
NOTICE: BL3-1: v1.0(release):801e730
NOTICE: BL3-1: Built : 22:09:38, Aug 10 2017
mpu_config_enable:ok
[Image: gxl_v1.1.3244-a3237e2 2017-08-16 14:01:18 hong.guo@droid04]
OPS=0x82
wdt: reset registers!
97 9d 1a 40 c6 e1 67 a3 67 5d 1c 84 [40.625205 Inits done]
secure task start!
high task start!
low task start!
ERROR: Error initializing runtime service opteed_fast
U-Boot 2020.04 (Nov 25 2020 - 12:38:23 +0800) khadas-vim2
Model: Khadas VIM2
SoC: Amlogic Meson GXM (S912) Revision 22:a (82:2)
DRAM: 3 GiB
MMC: mmc@70000: 0, mmc@72000: 1, mmc@74000: 2
Loading Environment from FAT... detect... booted from emmc...
OK
In: serial
Out: serial
Err: serial
[BL31]: tee size: 0
Net: eth0: ethernet@c9410000
Card did not respond to voltage select!
Card did not respond to voltage select!
6864 bytes read in 2 ms (3.3 MiB/s)
starting USB...
Bus dwc3@c9000000: Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.00
scanning bus dwc3@c9000000 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Setting bus to 1
Hit SPACE in 1 seconds to stop autoboot
Device 0: unknown device
Card did not respond to voltage select!
Card did not respond to voltage select!
switch to partitions #0, OK
mmc2(part 0) is current device
Scanning mmc 2:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
576 bytes read in 2 ms (281.3 KiB/s)
1: MANJARO
Retrieving file: /initramfs-linux.img
8553674 bytes read in 220 ms (37.1 MiB/s)
Retrieving file: /Image
30226944 bytes read in 872 ms (33.1 MiB/s)
append: initrd=/initramfs-linux.img root=LABEL=ROOT_MNJRO rootflags=data=writeback rw console=ttyAML0,115200n8 conh
Retrieving file: /dtbs/amlogic/meson-gxm-khadas-vim2.dtb
42161 bytes read in 6 ms (6.7 MiB/s)
## Flattened Device Tree blob at 08008000
Booting using the fdt blob at 0x8008000
Host not halted after 16000 microseconds.
Loading Ramdisk to bb6f1000, end bbf194ca ... OK
Loading Device Tree to 00000000bb6e3000, end 00000000bb6f04b0 ... OK
Starting kernel ...
[...]
Can you help me?