When I flash Edge_Ubuntu-server-bionic_Linux-5.5-rc2_arm64_EMMC_V0.8.3-20200110.img, even after fully erasing the eMMC, the boot process hangs at the same place every time. This is the firmware downloaded from the Khadas web site, not something I built. Board is Edge-V Pro. Same load in SD version boots fine.
Here is boot log:
.
.
.
[ 0.000000] uboot setup mac-addr: d6:33:c0:8d:67:ee
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] software IO TLB: mapped [mem 0x3bfff000-0x3ffff000] (64MB)
[ 0.000000] Memory: 3706124K/3897344K available (14012K kernel code, 886K rwdata, 5084K rodata, 960K init, 401K bss, 174836K reserved, 16384K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 256 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: no VLPI support, no direct LPI support
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fef00000
[ 0.000000] ITS [mem 0xfee20000-0xfee3ffff]
[ 0.000000] ITS@0x00000000fee20000: allocated 65536 Devices @f1c80000 (flat, esz 8, psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GICv3: using LPI property table @0x00000000f1c40000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000000f1c50000
[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[ 0.000000] GICv3: GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[ 0.000000] random: get_random_bytes called from start_kernel+0x2ac/0x440 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000010] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.002160] Console: colour dummy device 80x25
[ 0.003750] printk: console [tty0] enabled
[ 0.003930] Calibrating delay loop (skipped), value calculated using timer frequency… 48.00 BogoMIPS (lpj=96000)
[ 0.003990] pid_max: default: 32768 minimum: 301
[ 0.004211] LSM: Security Framework initializing
[ 0.004384] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.004461] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.004605] *** VALIDATE tmpfs ***
[ 0.005526] *** VALIDATE proc ***
[ 0.005996] *** VALIDATE cgroup1 ***
[ 0.006033] *** VALIDATE cgroup2 ***
[ 0.027749] ASID allocator initialised with 32768 entries
[ 0.035748] rcu: Hierarchical SRCU implementation.
[ 0.043993] Platform MSI: interrupt-controller@fee20000 domain created
[ 0.044615] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[ 0.045066] EFI services will not be available.
[ 0.051851] smp: Bringing up secondary CPUs …
[ 0.084314] Detected VIPT I-cache on CPU1
[ 0.084373] GICv3: CPU1: found redistributor 1 region 0:0x00000000fef20000
[ 0.084395] GICv3: CPU1: using allocated LPI pending table @0x00000000f1c60000
[ 0.084461] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.116496] Detected VIPT I-cache on CPU2
[ 0.116554] GICv3: CPU2: found redistributor 2 region 0:0x00000000fef40000
[ 0.116578] GICv3: CPU2: using allocated LPI pending table @0x00000000f1c70000
[ 0.116643] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.148693] Detected VIPT I-cache on CPU3
[ 0.148752] GICv3: CPU3: found redistributor 3 region 0:0x00000000fef60000
[ 0.148775] GICv3: CPU3: using allocated LPI pending table @0x00000000f1d00000
[ 0.148838] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.190338] CPU features: detected: EL2 vector hardening
[ 0.190701] ARM_SMCCC_ARCH_WORKAROUND_1 missing from firmware
[ 0.191025] CPU features: detected: ARM erratum 1319367
[ 0.191305] Detected PIPT I-cache on CPU4
[ 0.192560] GICv3: CPU4: found redistributor 100 region 0:0x00000000fef80000
[ 0.193018] GICv3: CPU4: using allocated LPI pending table @0x00000000f1d10000
[ 0.194258] CPU4: Booted secondary processor 0x0000000100 [0x410fd082]
[ 0.240313] Detected PIPT I-cache on CPU5
[ 0.241682] GICv3: CPU5: found redistributor 101 region 0:0x00000000fefa0000
[ 0.242151] GICv3: CPU5: using allocated LPI pending table @0x00000000f1d20000
[ 0.243372] CPU5: Booted secondary processor 0x0000000101 [0x410fd082]
[ 0.249461] smp: Brought up 1 node, 6 CPUs
[ 0.250123] SMP: Total of 6 processors activated.
[ 0.250165] CPU features: detected: 32-bit EL0 Support
[ 0.250206] CPU features: detected: CRC32 instructions
[ 0.262333] CPU: All CPU(s) started at EL2
[ 0.262941] alternatives: patching kernel code
[ 0.269236] devtmpfs: initialized
[ 0.297676] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.297897] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[ 0.299736] xor: measuring software checksum speed
[ 0.338391] 8regs : 768.000 MB/sec
[ 0.378656] 32regs : 943.000 MB/sec
[ 0.418941] arm64_neon: 764.000 MB/sec
[ 0.418975] xor: using function: 32regs (943.000 MB/sec)
[ 0.419092] pinctrl core: initialized pinctrl subsystem
[ 0.420920] thermal_sys: Registered thermal governor ‘step_wise’
[ 0.420938] thermal_sys: Registered thermal governor ‘user_space’
[ 0.422270] DMI not present or invalid.
[ 0.423282] NET: Registered protocol family 16
[ 0.451634] DMA: preallocated 2048 KiB pool for atomic allocations
[ 0.451736] audit: initializing netlink subsys (disabled)
[ 0.456359] audit: type=2000 audit(0.452:1): state=initialized audit_enabled=0 res=1
[ 0.459974] cpuidle: using governor menu
[ 0.461553] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.464451] Serial: AMBA PL011 UART driver
[ 0.573406] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.573551] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.573596] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.573636] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.737405] cryptd: max_cpu_qlen set to 1000
[ 1.028994] raid6: neonx8 gen() 541 MB/s
[ 1.097364] raid6: neonx8 xor() 507 MB/s
[ 1.165821] raid6: neonx4 gen() 503 MB/s
[ 1.234342] raid6: neonx4 xor() 478 MB/s
[ 1.302856] raid6: neonx2 gen() 392 MB/s
[ 1.371289] raid6: neonx2 xor() 399 MB/s
[ 1.439862] raid6: neonx1 gen() 246 MB/s
[ 1.508264] raid6: neonx1 xor() 284 MB/s
[ 1.576834] raid6: int64x8 gen() 329 MB/s
[ 1.645171] raid6: int64x8 xor() 250 MB/s
[ 1.713691] raid6: int64x4 gen() 349 MB/s
[ 1.782148] raid6: int64x4 xor() 255 MB/s
[ 1.850934] raid6: int64x2 gen() 229 MB/s
[ 1.918993] raid6: int64x2 xor() 201 MB/s
[ 1.987828] raid6: int64x1 gen() 151 MB/s
[ 2.056004] raid6: int64x1 xor() 148 MB/s
[ 2.056036] raid6: using algorithm neonx8 gen() 541 MB/s
[ 2.056070] raid6: … xor() 507 MB/s, rmw enabled
[ 2.056101] raid6: using neon recovery algorithm
[ 2.060803] vsys_3v3: supplied by vsys
[ 2.061533] vsys_5v0: supplied by vsys
[ 2.062020] vcc3v3_pcie: supplied by vsys_3v3
[ 2.064935] iommu: Default domain type: Translated
[ 2.070333] vgaarb: loaded
[ 2.071230] SCSI subsystem initialized
[ 2.073784] usbcore: registered new interface driver usbfs
[ 2.073908] usbcore: registered new interface driver hub
[ 2.074264] usbcore: registered new device driver usb
[ 2.075163] pps_core: LinuxPPS API ver. 1 registered
[ 2.075202] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 2.075271] PTP clock support registered
[ 2.075856] EDAC MC: Ver: 3.0.0
[ 2.077755] Advanced Linux Sound Architecture Driver Initialized.
[ 2.078924] NetLabel: Initializing
[ 2.078956] NetLabel: domain hash size = 128
[ 2.078984] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 2.079145] NetLabel: unlabeled traffic allowed by default
[ 2.082463] clocksource: Switched to clocksource arch_sys_counter
[ 2.083321] VFS: Disk quotas dquot_6.6.0
[ 2.083502] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.083674] *** VALIDATE ramfs ***
[ 2.083736] *** VALIDATE hugetlbfs ***
[ 2.100961] NET: Registered protocol family 2
[ 2.102707] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 2.102911] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 2.103576] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[ 2.104720] TCP: Hash tables configured (established 32768 bind 32768)
[ 2.105229] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 2.105488] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 2.106881] NET: Registered protocol family 1
[ 2.110420] RPC: Registered named UNIX socket transport module.
[ 2.110459] RPC: Registered udp transport module.
[ 2.110490] RPC: Registered tcp transport module.
[ 2.110519] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.110568] PCI: CLS 0 bytes, default 64
[ 2.111009] Trying to unpack rootfs image as initramfs…
[ 3.009023] Freeing initrd memory: 7284K
[ 3.020771] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 3.024315] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[ 3.026040] kvm [1]: IPA Size Limit: 40bits
[ 3.028081] kvm [1]: vgic-v2@fff20000
[ 3.028284] kvm [1]: GIC system register CPU interface enabled
[ 3.032210] kvm [1]: vgic interrupt IRQ10
[ 3.035482] kvm [1]: Hyp mode initialized successfully
[ 3.371785] Initialise system trusted keyrings
[ 3.373495] workingset: timestamp_bits=44 max_order=20 bucket_order=0
[ 3.392752] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.396269] NFS: Registering the id_resolver key type
[ 3.396438] Key type id_resolver registered
[ 3.396471] Key type id_legacy registered
[ 3.396519] nfs4filelayout_init: NFSv4 File Layout Driver Registering…
[ 3.396557] Installing knfsd (copyright © 1996 okir@monad.swb.de).
[ 3.399381] fuse: init (API version 7.31)
[ 3.399628] *** VALIDATE fuse ***
[ 3.399670] *** VALIDATE fuse ***
[ 3.400569] SGI XFS with ACLs, security attributes, realtime, quota, no debug enabled
[ 3.406668] *** VALIDATE xfs ***
[ 3.406771] 9p: Installing v9fs 9p2000 file system support
[ 3.468877] NET: Registered protocol family 38
[ 3.469058] Key type asymmetric registered
[ 3.469093] Asymmetric key parser ‘x509’ registered
[ 3.469549] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 3.471372] io scheduler mq-deadline registered
[ 3.471416] io scheduler kyber registered
[ 3.472065] io scheduler bfq registered
[ 3.479534] vcc5v0_host: supplied by vsys_5v0
[ 3.498700] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 3.498848] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[ 3.502697] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 3.502776] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[ 3.507060] pwm-regulator: supplied by regulator-dummy
[ 3.508914] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[ 3.513940] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 37, base_baud = 1500000) is a 16550A
[ 3.514648] serial serial0: tty port ttyS0 registered
[ 3.516077] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 38, base_baud = 1500000) is a 16550A
[ 3.635652] printk: console [ttyS2] enabled
[ 3.648713] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 3.668069] brd: module loaded
[ 3.693085] loop: module loaded
[ 4.672269] libphy: Fixed MDIO Bus: probed
[ 4.705526] tun: Universal TUN/TAP device driver, 1.6
[ 4.807252] e1000e: Intel® PRO/1000 Network Driver - 3.2.6-k
[ 4.808970] e1000e: Copyright© 1999 - 2015 Intel Corporation.
[ 4.813271] igb: Intel® Gigabit Ethernet Network Driver - version 5.6.0-k
[ 4.815726] igb: Copyright © 2007-2014 Intel Corporation.
[ 4.819700] igbvf: Intel® Gigabit Virtual Function Network Driver - version 2.4.0-k
[ 4.821677] igbvf: Copyright © 2009 - 2012 Intel Corporation.
[ 4.892344] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
[ 4.895140] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
[ 4.901813] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
[ 4.905572] rk_gmac-dwmac fe300000.ethernet: phy regulator is not available yet, deferred probing
[ 4.919442] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 4.921175] usbcore: registered new interface driver pegasus
[ 4.921802] usbcore: registered new interface driver rtl8150
[ 4.922537] usbcore: registered new interface driver r8152
[ 4.923118] usbcore: registered new interface driver dm9601
[ 4.923733] usbcore: registered new interface driver CoreChips
[ 4.924369] usbcore: registered new interface driver smsc75xx
[ 4.924999] usbcore: registered new interface driver smsc95xx
[ 4.925602] usbcore: registered new interface driver plusb
[ 4.926217] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 4.930275] VFIO - User Level meta-driver version: 0.3
[ 4.948952] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 4.949772] ehci-pci: EHCI PCI platform driver
[ 4.950443] ehci-platform: EHCI generic platform driver
[ 4.954369] ehci-platform fe380000.usb: EHCI Host Controller
[ 4.954950] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 1
[ 4.956013] ehci-platform fe380000.usb: irq 31, io mem 0xfe380000
[ 4.970512] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[ 4.971519] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05
[ 4.972292] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.972965] usb usb1: Product: EHCI Host Controller
[ 4.973427] usb usb1: Manufacturer: Linux 5.5.0-rc2 ehci_hcd
[ 4.973957] usb usb1: SerialNumber: fe380000.usb
[ 4.980774] hub 1-0:1.0: USB hub found
[ 4.981192] hub 1-0:1.0: 1 port detected
[ 4.985498] ehci-platform fe3c0000.usb: EHCI Host Controller
[ 4.986084] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 2
[ 4.987104] ehci-platform fe3c0000.usb: irq 33, io mem 0xfe3c0000
[ 5.002373] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[ 5.003266] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05
[ 5.004039] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.004712] usb usb2: Product: EHCI Host Controller
[ 5.005174] usb usb2: Manufacturer: Linux 5.5.0-rc2 ehci_hcd
[ 5.005704] usb usb2: SerialNumber: fe3c0000.usb
[ 5.009862] hub 2-0:1.0: USB hub found
[ 5.010371] hub 2-0:1.0: 1 port detected
[ 5.013492] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 5.014643] ohci-pci: OHCI PCI platform driver
[ 5.015500] ohci-platform: OHCI generic platform driver
[ 5.017314] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[ 5.017975] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 3
[ 5.019053] ohci-platform fe3a0000.usb: irq 32, io mem 0xfe3a0000
[ 5.082982] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.05
[ 5.083755] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.084429] usb usb3: Product: Generic Platform OHCI controller
[ 5.084982] usb usb3: Manufacturer: Linux 5.5.0-rc2 ohci_hcd
[ 5.085516] usb usb3: SerialNumber: fe3a0000.usb
[ 5.089712] hub 3-0:1.0: USB hub found
[ 5.090213] hub 3-0:1.0: 1 port detected
[ 5.091832] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[ 5.092497] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 4
[ 5.093566] ohci-platform fe3e0000.usb: irq 34, io mem 0xfe3e0000
[ 5.158522] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.05
[ 5.159297] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.159971] usb usb4: Product: Generic Platform OHCI controller
[ 5.160524] usb usb4: Manufacturer: Linux 5.5.0-rc2 ohci_hcd
[ 5.161054] usb usb4: SerialNumber: fe3e0000.usb
[ 5.165302] hub 4-0:1.0: USB hub found
[ 5.165722] hub 4-0:1.0: 1 port detected
[ 5.172701] usbcore: registered new interface driver usb-storage
[ 5.181885] i2c /dev entries driver
[ 5.193656] rk808 4-001b: chip id: 0x0
[ 5.203524] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 5.204288] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 5.205209] DCDC_REG1: supplied by vsys_3v3
[ 5.207393] DCDC_REG2: supplied by vsys_3v3
[ 5.208770] DCDC_REG3: supplied by vsys_3v3
[ 5.209768] DCDC_REG4: supplied by vsys_3v3
[ 5.211278] LDO_REG1: supplied by vsys_3v3
[ 5.213289] LDO_REG2: supplied by vsys_3v3
[ 5.215059] LDO_REG3: supplied by vsys_3v3
[ 5.216925] LDO_REG4: supplied by vsys_3v3
[ 5.218809] LDO_REG5: supplied by vsys_3v3
[ 5.220536] LDO_REG6: supplied by vsys_3v3
[ 5.222459] LDO_REG7: supplied by vsys_3v3
[ 5.224202] LDO_REG8: supplied by vsys_3v3
[ 5.226179] SWITCH_REG1: supplied by vsys_3v3
[ 5.227147] SWITCH_REG2: supplied by vsys_3v3
[ 5.235771] rk808-rtc rk808-rtc: registered as rtc0
[ 5.238804] fan53555-regulator 4-0040: FAN53555 Option[8] Rev[1] Detected!
[ 5.239508] fan53555-reg: supplied by vsys_3v3
[ 5.241683] vcc1v8_s3: supplied by vcc_1v8
[ 5.243572] fan53555-regulator 4-0041: FAN53555 Option[8] Rev[1] Detected!
[ 5.244256] fan53555-reg: supplied by vsys_3v3
[ 5.272395] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 400000 KHz
[ 5.274070] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 408000 KHz
[ 5.277048] random: fast init done
[ 5.278817] cpufreq: cpufreq_online: CPU4: Running at unlisted freq: 12000 KHz
[ 5.289898] cpufreq: cpufreq_online: CPU4: Unlisted initial frequency changed to: 408000 KHz
[ 5.292597] sdhci: Secure Digital Host Controller Interface driver
[ 5.293163] sdhci: Copyright© Pierre Ossman
[ 5.293591] Synopsys Designware Multimedia Card Interface Driver
[ 5.295717] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[ 5.296361] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[ 5.296963] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[ 5.297491] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 28,32 bit host data width,256 deep fifo
[ 5.298461] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
[ 5.298981] mmc_host mmc0: card is non-removable.
[ 5.313455] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 5.328316] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
[ 5.329002] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
[ 5.329624] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
[ 5.330246] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 29,32 bit host data width,256 deep fifo
[ 5.331334] dwmmc_rockchip fe320000.dwmmc: Got CD GPIO
[ 5.344792] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 5.358919] sdhci-pltfm: SDHCI platform and OF driver helper
[ 5.360777] mmc2: CQHCI version 5.10
[ 5.372926] mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
[ 5.375006] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
[ 5.377083] mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
[ 5.380512] mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
[ 5.384540] mmc0: queuing unknown CIS tuple 0x81 (9 bytes)
[ 5.386885] mmc2: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[ 5.389891] ledtrig-cpu: registered to indicate activity on CPUs
[ 5.392997] usbcore: registered new interface driver usbhid
[ 5.393521] usbhid: USB HID core driver
[ 5.403778] xt_time: kernel timezone is -0000
[ 5.404203] IPVS: Registered protocols (TCP, UDP, SCTP, AH, ESP)
[ 5.404767] IPVS: Connection hash table configured (size=4096, memory=64Kbytes)
[ 5.405565] IPVS: ipvs loaded.
[ 5.405842] IPVS: [rr] scheduler registered.
[ 5.406257] IPVS: [wrr] scheduler registered.
[ 5.406646] IPVS: [lc] scheduler registered.
[ 5.407026] IPVS: [wlc] scheduler registered.
[ 5.407415] IPVS: [fo] scheduler registered.
[ 5.407795] IPVS: [ovf] scheduler registered.
[ 5.408192] IPVS: [lblc] scheduler registered.
[ 5.408594] IPVS: [lblcr] scheduler registered.
[ 5.408997] IPVS: [dh] scheduler registered.
[ 5.409377] IPVS: [sh] scheduler registered.
[ 5.409757] IPVS: [sed] scheduler registered.
[ 5.410237] IPVS: [nq] scheduler registered.
[ 5.410795] Initializing XFRM netlink socket
[ 5.411232] NET: Registered protocol family 17
[ 5.411811] 8021q: 802.1Q VLAN Support v1.8
[ 5.412307] 9pnet: Installing 9P2000 support
[ 5.412738] Key type dns_resolver registered
[ 5.413719] registered taskstats version 1
[ 5.414117] Loading compiled-in X.509 certificates
[ 5.417074] zswap: default zpool zbud not available
[ 5.417531] zswap: pool creation failed
[ 5.418926] Btrfs loaded, crc32c=crc32c-generic
[ 5.439365] mmc_host mmc0: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
[ 5.453740] rk_gmac-dwmac fe300000.ethernet: IRQ eth_wake_irq not found
[ 5.453752] mmc2: mmc_select_hs400es failed, error -110
[ 5.454418] rk_gmac-dwmac fe300000.ethernet: IRQ eth_lpi not found
[ 5.454866] mmc2: error -110 whilst initialising MMC card
[ 5.455485] rk_gmac-dwmac fe300000.ethernet: PTP uses main clock
[ 5.456538] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[ 5.457165] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[ 5.457667] rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
[ 5.458196] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[ 5.458779] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[ 5.459394] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[ 5.464941] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[ 5.465625] rk_gmac-dwmac fe300000.ethernet: User ID: 0x10, Synopsys ID: 0x35
[ 5.466274] rk_gmac-dwmac fe300000.ethernet: DWMAC1000
[ 5.466738] rk_gmac-dwmac fe300000.ethernet: DMA HW capability register supported
[ 5.467401] rk_gmac-dwmac fe300000.ethernet: RX Checksum Offload Engine supported
[ 5.468062] rk_gmac-dwmac fe300000.ethernet: COE Type 2
[ 5.468526] rk_gmac-dwmac fe300000.ethernet: TX Checksum insertion supported
[ 5.469148] rk_gmac-dwmac fe300000.ethernet: Wake-Up On Lan supported
[ 5.469739] rk_gmac-dwmac fe300000.ethernet: Normal descriptors
[ 5.470271] rk_gmac-dwmac fe300000.ethernet: Ring mode enabled
[ 5.470789] rk_gmac-dwmac fe300000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 5.559758] mmc2: mmc_select_hs400es failed, error -110
[ 5.560246] mmc2: error -110 whilst initialising MMC card
[ 5.570933] libphy: stmmac: probed
[ 5.571279] RTL8211F Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[ 5.572401] RTL8211F Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[ 5.577252] input: adc-keys as /devices/platform/adc-keys/input/input0
[ 5.582675] input: gpio-keys as /devices/platform/gpio-keys/input/input1
[ 5.585536] rk808-rtc rk808-rtc: setting system clock to 2013-01-18T08:50:20 UTC (1358499020)
[ 5.586991] ALSA device list:
[ 5.587279] No soundcards found.
[ 5.588111] Freeing unused kernel memory: 960K
[ 5.614376] Run /init as init process
[ 5.677520] mmc2: mmc_select_hs400es failed, error -110
[ 5.678011] mmc2: error -110 whilst initialising MMC card
[ 5.707318] dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 196
[ 5.713288] mmc0: new ultra high speed SDR104 SDIO card at address 0001
[ 5.841266] mmc2: mmc_select_hs400es failed, error -110
[ 5.841768] mmc2: error -110 whilst initialising MMC card
[ 5.952413] OF: graph: no port node found in /syscon@ff770000/usb2-phy@e450/otg-port
[ 5.954621] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.955136] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 5
[ 5.955943] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[ 5.956817] xhci-hcd xhci-hcd.0.auto: irq 226, io mem 0xfe800000
[ 5.957793] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05
[ 5.958651] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.959300] usb usb5: Product: xHCI Host Controller
[ 5.959735] usb usb5: Manufacturer: Linux 5.5.0-rc2 xhci-hcd
[ 5.960238] usb usb5: SerialNumber: xhci-hcd.0.auto
[ 5.961343] hub 5-0:1.0: USB hub found
[ 5.962154] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.962724] hub 5-0:1.0: 1 port detected
[ 5.963384] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 6
[ 5.964195] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[ 5.965077] xhci-hcd xhci-hcd.1.auto: irq 227, io mem 0xfe900000
[ 5.965901] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05
[ 5.966660] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.967300] usb usb6: Product: xHCI Host Controller
[ 5.967735] usb usb6: Manufacturer: Linux 5.5.0-rc2 xhci-hcd
[ 5.968237] usb usb6: SerialNumber: xhci-hcd.1.auto
[ 5.968836] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 5.969701] hub 6-0:1.0: USB hub found
[ 5.970092] hub 6-0:1.0: 1 port detected
[ 5.970787] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[ 5.971292] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 7
[ 5.971978] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[ 5.972612] usb usb7: We don’t know the algorithms for LPM for this host, disabling LPM.
[ 5.973407] usb usb7: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.05
[ 5.974157] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.974796] usb usb7: Product: xHCI Host Controller
[ 5.975232] usb usb7: Manufacturer: Linux 5.5.0-rc2 xhci-hcd
[ 5.975734] usb usb7: SerialNumber: xhci-hcd.1.auto
[ 5.982434] hub 7-0:1.0: USB hub found
[ 5.982805] hub 7-0:1.0: 1 port detected
[ 5.983393] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 8
[ 5.984082] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 5.984716] usb usb8: We don’t know the algorithms for LPM for this host, disabling LPM.
[ 5.985511] usb usb8: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.05
[ 5.986270] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.986910] usb usb8: Product: xHCI Host Controller
[ 5.987344] usb usb8: Manufacturer: Linux 5.5.0-rc2 xhci-hcd
[ 5.987846] usb usb8: SerialNumber: xhci-hcd.0.auto
[ 5.988601] hub 8-0:1.0: USB hub found
[ 5.988956] hub 8-0:1.0: 1 port detected
[ 6.306154] usb 6-1: new high-speed USB device number 2 using xhci-hcd
[ 6.466606] usb 6-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=92.24
[ 6.467386] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.468049] usb 6-1: Product: USB2.0 Hub
[ 6.468424] usb 6-1: Manufacturer: GenesysLogic
[ 6.517989] hub 6-1:1.0: USB hub found
[ 6.519217] hub 6-1:1.0: 4 ports detected
[ 6.586366] usb 7-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[ 6.608963] usb 7-1: New USB device found, idVendor=05e3, idProduct=0616, bcdDevice=92.24
[ 6.609714] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.610371] usb 7-1: Product: USB3.0 Hub
[ 6.610732] usb 7-1: Manufacturer: GenesysLogic
[ 6.629499] hub 7-1:1.0: USB hub found
[ 6.630201] hub 7-1:1.0: 4 ports detected
[ 6.882238] usb 6-1.1: new low-speed USB device number 3 using xhci-hcd
[ 6.988276] usb 6-1.1: New USB device found, idVendor=413c, idProduct=2112, bcdDevice= 1.07
[ 6.989056] usb 6-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.989738] usb 6-1.1: Product: Dell USB Wired Multimedia Keyboard
[ 6.990354] usb 6-1.1: Manufacturer: DELL
[ 7.065912] input: DELL Dell USB Wired Multimedia Keyboard as /devices/platform/usb@fe900000/fe900000.dwc3/xhci-hcd.1.auto/usb6/6-1/6-1.1/6-1.1:1.0/0003:413C:2112.0001/input/input2
[ 7.127156] hid-generic 0003:413C:2112.0001: input: USB HID v1.10 Keyboard [DELL Dell USB Wired Multimedia Keyboard] on usb-xhci-hcd.1.auto-1.1/input0
[ 7.135804] input: DELL Dell USB Wired Multimedia Keyboard System Control as /devices/platform/usb@fe900000/fe900000.dwc3/xhci-hcd.1.auto/usb6/6-1/6-1.1/6-1.1:1.1/0003:413C:2112.0002/input/input3
[ 7.194421] input: DELL Dell USB Wired Multimedia Keyboard Consumer Control as /devices/platform/usb@fe900000/fe900000.dwc3/xhci-hcd.1.auto/usb6/6-1/6-1.1/6-1.1:1.1/0003:413C:2112.0002/input/input4
[ 7.196103] hid-generic 0003:413C:2112.0002: input: USB HID v1.10 Device [DELL Dell USB Wired Multimedia Keyboard] on usb-xhci-hcd.1.auto-1.1/input1
[ 7.282202] usb 6-1.2: new low-speed USB device number 4 using xhci-hcd
[ 7.387787] usb 6-1.2: New USB device found, idVendor=046d, idProduct=c063, bcdDevice=57.00
[ 7.388584] usb 6-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 7.389265] usb 6-1.2: Product: DELL USB Laser Mouse
[ 7.389734] usb 6-1.2: Manufacturer: DELL
[ 7.450716] input: DELL DELL USB Laser Mouse as /devices/platform/usb@fe900000/fe900000.dwc3/xhci-hcd.1.auto/usb6/6-1/6-1.2/6-1.2:1.0/0003:046D:C063.0003/input/input5
[ 7.452423] hid-generic 0003:046D:C063.0003: input: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-xhci-hcd.1.auto-1.2/input0
[ 7.534187] usb 6-1.4: new low-speed USB device number 5 using xhci-hcd
[ 8.391489] usb 6-1-port4: Cannot enable. Maybe the USB cable is bad?
[ 12.168308] phy phy-ff770000.syscon:usb2-phy@e450.2: charger = USB_SDP_CHARGER
