kernel\arch\arm64\boot\dts\rockchip.rk3399-khadas-edge-android.dtb.dts.tmp
@BarryS Post the contents of this document.
It was too large to post so I put it on google docs-
Kernel\arch\arm64\boot\dts\rockchip.rk3399-khadas-edge-android.dtb.dts.tmp
Did you erase the flash before upgrading the firmware?
If not, erase the flash before upgrading the firmware.
Still not working-
I erased the flash with sudo ./upgrade_tool ef /path/to/MiniLoaderAll.bin
Then flashed with the new android build. This time it again shows the u-boot splash (on HDMI) and then appears to just turn off. eDP is dark the whole time. As I’m typing this a few minutes later, it is waking up and then doing the same cycle of starting to boot and then going to sleep again.
Did you see anything in the .tmp file that looked wrong?
no problem. Send the boot log.
I’m having a difficult time getting the serial connection to work. I’ve tried 2 different serial adapters -
I keep getting gibberish- This is booting the Android10 build unmodified that boots successfully.
Any other way to get the boot log? Or have you seen this issue with the serial terminal before. Same thing happens on another EdgeV, but when I hook my Mac up to a RaspberryPi I can get the linux boot console on the same serial tool???
bs@Bs-MBP-2 ~ % kermit
Connecting to /dev/tty.usbserial-AQ00L2V5, speed 115200
Escape character: Ctrl-\ (ASCII 28, FS): enabled
Type the escape character followed by C to get back,
or followed by ? to see other options.
?{{i???m?B?j?B?Z{???G???3?V{?wggoffgFWgGfgGFgGFgGfgFVFGFGFgGFgg^GgGFGFgGVggwg?o???z??{{z{??{y{y?FngOy{?vf&WgO?FF’G?vGgFNNFWfvWgW_gN_WgOFfOGgVGf~O^e&?oG_W??WWGOgofgG_GgWwOgFff?/gfffNf
ͭum??]???9?%??
?-??5,?K??
???-??U? M
%}?=???-?
E???{???y?x??????Wf?F_?F?~gF?fgn?Wn_nf_OngnwWf__FgNW~NWoOn_NgG_fFWNo~OwfFW_nOOnwffGFNFF~Wnf_fOG~f^v?N?fF_fOofGOfovn_fOVfGfOW~Nwfw_fw_fg?gvggVGfog_FgfoGgNfgO’?ngffGnVg_GvGGWonG__wgvW_n’~v~nOv_wV_wfVvg_v_Gfg~ww_wWOnwfwV_n’nwgvwOGWvWnfgVvwvgVvOFNoOvg&gvwVG~WgwfGGVwG~Gvo_gf_ov_G~g_VGwf~g6gWvWW~WFO?vWGvovO?vovOg_OvGvGFWn?vngngggfvOg_vO_vOgO6OGGG7NfnvOG_~onvOGnvvOgfgvggGnG?WG_nwWfWw_f/VOnfgW?GGowv_O~WvGv_ON_ON_O^ov_OfOv_O~n_OfOf_O_F’N_FWNn_fOOfOf_fOf_WfOOF&fwn__n_Of~wGfOwfOGWW^nfO^GfOwWnG^ogfGOfgf_7_WvWfOGFWwfogOfO^O_FOfoGfOff~fOwFw_OFOOOO^g__fOwfOGNgOfgOV^v~GfOWvo~F__GWVGng_gVGO"6>?.G?&?Ӣ&fKfWfWV_fOV_OfO_OF_WOfO_VOFWfOWOfOO_v_W_fOWnffOOVWfOOf__OWWfGwNfnGfGwfffoFFfofGfofoFfoFfoFffVfonvnFnfwF?GGwGnO_7nwwoFfOVoG?VowgfGG~gOvGVoFgfWgGgFo~gvGgoV/GFw?nngo7fNW_NgF??Nfg~fO_nf~fOOo_wnf_OFOfO^NFNWwfO_~O^Vggg^f_oFgw’V__vgFg^GOv_GgGg^g_fo__FggngggvWNg~f7WGfO^fO_oGfWWFg_FGgfogvo~vNGWnfGoO_vG/nGGfn_nf/GgvowooW/FGGFGwOogOFG_vwfWVg^VWWnOGwwoNVWgWOff?Fo?Vg_VgvOGWw^g_V_Gv_vvog_~V_vVv^6ovg_ovGG^goNgvg_o?VOGOVG?gG6nggwoog?FoGw?fF?ON#GWfGVvOGOgnwoFovOFgvO_OFog_WfO_fOfOfnf_N_ww~f/fGo~g’/foN_fgFfWfNFWfGGfWWnfoo_ff7fgf7oFfOGngF7fwWNwfWFWoNOFnwoJG_fofo_Ogf_GNGf_Nwof_f_vV^GNn?G’~O_wgGNnGWGNWf__gN_GWf_F&nnfg_fwwnO_N~/~#ggfgGnOgG&foVfOg_VG__Gfog_'ffg6fGgG~ooWNFgW_gvg_FG?VF?FgGFONgoGnwoNgOGv_o__ovW_nW_OOgGW_vg^~wfw~WvgGvOOVG~wvVvOgGWOWV^FO_WfGwfgGvOOvwWv~Wn_g_vOWoOg_onofGVg_WVwVOWvwvoovvOnFVGNvO?FOf?Fo?fggFV____FfwfnfGwfwWN_GFGGFoGG&?~/~?N~VOF__fogfg~wn_F_gONFgo_Fgo_nW^N_OFgwVwG^nogf~WGGWGwfWOGwgF~n^OFnwfOFFwf?Gv_fgV??&.^VNfOongVwovOwoongFNv_Ff_vW.N~nv~&F~V_g_VFvVg_Fv_V?nGWG_ofG^Goofng~wnWFffoVofoVFfoV~O’FoonffnnfFWGFg~VOgo6VgOnOVoVoFoOVooFnov?NoOVwBgvGV?V_Nf^GW??n^vg_fF_NofWo_fFg^vOGGFWGV?fWFOgGf_wNfFNGf^OfnOoV?vo_F^vo[Gw_ooO^GGW?f_ow??WGowWwoOVoWgwwoFo?Of_WwO?oWGfoWGG/wF^Oo??nnWgFwFVGgNGWvgGOwfooffgONWfgWfgffWFggg_oVgWgWwwn?o?OfOOwGoowfowogWWoggw_ooW_OOwoFoOw_GV_nfonfWFF?f_FOFG_Oofo_F?g^v~OnoVWnG^?wV_fWgwNof?f_wW_fWffW.fWWF/voFFO^Ng^ov~?oFG_GovoW_^Wwwfo?wgWW?Owof/WW?WwfgWg?wfgWgFoVgVno?VgWg?WwN_?wn_?wvgWWWo?GWVV_
Hello, The Edges use a higher buad rate…
From Khadas Docs for the Edge…
" A Serial Debugging Tool. In this guide, we will use a USB to TTL Converter. Ensure that it supports the 1500000 baudrate."
By the way, I had trouble with serial to USB tools using the Prolific PL2303 chipset. Can you post what chipset your tools are using?
I’ve been trying 1500000 as well.
I’m using this one - https://www.amazon.com/gp/product/B07RBKCW3S/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1. which uses a FTDI FT232 chip
I was having trouble with the USB-C to USB-A adapter! But now I have the log messages working - thanks!
OK - thanks for the help with the Serial Debugging. I was able to pull the log file. Here is the outbox of the boot sequence on the Failed boot with the changes listed above to kernel/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge-android.dts
Here is the file with the boot log- (I haven’t looked through it yet)
BootLog on Failed Boot
Followup with more info -
I can see the eDP being recognized during the U-Boot boot sequence. Timings look good, I think. I’ve attached the display timings form the data sheet.
Also - Found this in the log file -
[ 1.572086] rockchip-pinctrl pinctrl: pin gpio4-23 already requested by ff940000.hdmi; cannot claim for ff970000.edp
[ 1.572104] rockchip-pinctrl pinctrl: pin-151 (ff970000.edp) status -22
[ 1.572114] rockchip-pinctrl pinctrl: could not request pin 151 (gpio4-23) from group edp-hpd on device rockchip-pinctrl
[ 1.572122] rockchip-dp ff970000.edp: Error applying setting, reverse things back
[ 1.572141] rockchip-dp: probe of ff970000.edp failed with error -22
Looks like a Gpio pin conflict with gpio4
Have you made any changes to the DTS file yourself?
@BarryS It is suggested that you can go to Android 9.0 platform for verification. After all, EDP has not been verified on Android 10.0 platform.
Yep - saw that pinctrl error. No I did not make any other changes to any files in the build.
My project requires dual touch screen support which requires Android10. Any other ideas?
android 9.0 support dual touch screen…
Can you double check - My understanding is that Android 9 supports dual displays but not dual touch. Dual touch screens was implemented in Android10.
refer to - https://source.android.com/devices/tech/display/multi_display/input-routing
Is that article incorrect?
It seems to be a common misunderstanding.
Edge android 10.0
hlm@Server:/users/hlm/Rockcip_Android10.0_SDK/kernel$ git diff arch/arm64/boot/dts/rockchip/rk3399.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index 6311964..0980dcd 100755
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -2152,10 +2152,8 @@
compatible = "rockchip,rk3399-edp";
reg = <0x0 0xff970000 0x0 0x8000>;
interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH 0>;
- clocks = <&cru PCLK_EDP>, <&cru PCLK_EDP_CTRL>, <&cru PCLK_VIO_GRF>;
- clock-names = "dp", "pclk", "grf";
- pinctrl-names = "default";
- pinctrl-0 = <&edp_hpd>;
+ clocks = <&cru PCLK_EDP>, <&cru PCLK_EDP_CTRL>;
+ clock-names = "dp", "pclk";
power-domains = <&power RK3399_PD_EDP>;
resets = <&cru SRST_P_EDP_CTRL>;
reset-names = "dp";
Edge android 10.0 edp(vob) + hdmi (vol)
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2018 Fuzhou Rockchip Electronics Co., Ltd
*/
/dts-v1/;
#include "rk3399-khadas-edge.dtsi"
#include <dt-bindings/sensor-dev.h>
#include <dt-bindings/input/input.h>
/ {
compatible = "Khadas,edge", "rockchip,rk3399";
khadas-matrix-keypad {
status = "okay";
compatible = "khadas-matrix-keypad";
row_col_gpio =
<&gpio0 10 GPIO_ACTIVE_HIGH>,
<&gpio0 11 GPIO_ACTIVE_HIGH>,
<&gpio0 12 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&matrix_gpio>;
debounce-delay-ms = <10>;
col-scan-delay-us = <10>;
linux,no-autorepeat;
};
edp_panel: edp-panel {
compatible = "simple-panel";
backlight = <&backlight>;
bus-format = <MEDIA_BUS_FMT_RGB888_1X24>;
power-supply = <&vcc3v3_s0>;
reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_HIGH>; /* GPIO4_D4 */
enable-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_HIGH>; /* GPIO4_D5 */
prepare-delay-ms = <20>;
enable-delay-ms = <20>;
ports {
panel_in_edp: endpoint {
remote-endpoint = <&edp_out_panel>;
};
};
display-timings {
native-mode = <&timing0>;
timing0: timing0 {
clock-frequency = <145500000>;
hactive = <1920>;
vactive = <1080>;
hfront-porch = <48>;
hsync-len = <32>;
hback-porch = <80>;
vfront-porch = <3>;
vsync-len = <5>;
vback-porch = <23>;
hsync-active = <0>;
vsync-active = <0>;
de-active = <0>;
pixelclk-active = <0>;
};
};
};
rt5651-sound {
status = "okay";
compatible = "simple-audio-card";
pinctrl-names = "default";
pinctrl-0 = <&rt5651_hpdet>;
simple-audio-card,format = "i2s";
simple-audio-card,name = "realtek,rt5651-codec";
simple-audio-card,mclk-fs = <256>;
simple-audio-card,hp-det-gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
simple-audio-card,widgets =
"Microphone", "Mic Jack",
"Headphone", "Headphone Jack";
simple-audio-card,routing =
"Mic Jack", "MICBIAS1",
"IN1P", "Mic Jack",
"Headphone Jack", "HPOL",
"Headphone Jack", "HPOR";
simple-audio-card,cpu {
sound-dai = <&i2s1>;
};
simple-audio-card,codec {
sound-dai = <&rt5651>;
};
};
};
&fusb0 {
status = "okay";
max-input-voltage = <13000000>;
max-input-current = <6000000>;
charge-dev = <&bq25703>;
};
&fusb1 {
status = "okay";
max-input-voltage = <13000000>;
max-input-current = <6000000>;
charge-dev = <&bq25703>;
};
&i2s1 {
status = "okay";
rockchip,i2s-broken-burst-len;
rockchip,playback-channels = <2>;
rockchip,capture-channels = <2>;
#sound-dai-cells = <0>;
};
&isp0_mmu {
status = "okay";
};
&isp1_mmu {
status = "okay";
};
&i2c0 {
status = "okay";
i2c-scl-rising-time-ns = <300>;
i2c-scl-falling-time-ns = <15>;
};
&i2c1 {
status = "okay";
i2c-scl-rising-time-ns = <300>;
i2c-scl-falling-time-ns = <15>;
rt5651: rt5651@1a {
#sound-dai-cells = <0>;
compatible = "rockchip,rt5651";
reg = <0x1a>;
clocks = <&cru SCLK_I2S_8CH_OUT>;
clock-names = "mclk";
pinctrl-names = "default";
pinctrl-0 = <&i2s_8ch_mclk>;
status = "okay";
};
};
&i2c6 {
status = "okay";
vm149c: vm149c@0c {
compatible = "silicon touch,vm149c";
status = "okay";
reg = <0x0c>;
rockchip,camera-module-index = <0>;
rockchip,camera-module-facing = "back";
};
imx214b: imx214b@10 {
compatible = "sony,imx214";
status = "okay";
reg = <0x10>;
clocks = <&cru SCLK_CIF_OUT>;
clock-names = "xvclk";
/* avdd-supply = <>; */
/* dvdd-supply = <>; */
/* dovdd-supply = <>; */
/* reset-gpios = <>; */
pwdn-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
pinctrl-names = "rockchip,camera_default";
pinctrl-0 = <&cif_clkout>;
rockchip,camera-module-index = <0>;
rockchip,camera-module-facing = "back";
rockchip,camera-module-name = "YG9626-S600Y7-C";
rockchip,camera-module-lens-name = "LG-50013A7";
lens-focus = <&vm149c>;
port {
ucam_out0: endpoint {
remote-endpoint = <&mipi_in_ucam0>;
//remote-endpoint = <&mipi_in_ucam1>;
data-lanes = <1 2>;
};
};
};
vm149c_front: vm149c_front@0c {
compatible = "silicon touch,vm149c";
status = "okay";
reg = <0x0c>;
rockchip,camera-module-index = <1>;
rockchip,camera-module-facing = "front";
};
imx214f: imx214f@10 {
compatible = "sony,imx214";
status = "okay";
reg = <0x10>;
clocks = <&cru SCLK_CIF_OUT>;
clock-names = "xvclk";
/* avdd-supply = <>; */
/* dvdd-supply = <>; */
/* dovdd-supply = <>; */
/* reset-gpios = <>; */
pwdn-gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
pinctrl-names = "rockchip,camera_default";
pinctrl-0 = <&cif_clkout>;
rockchip,camera-module-index = <1>;
rockchip,camera-module-facing = "front";
rockchip,camera-module-name = "YG9626-S600Y7-C";
rockchip,camera-module-lens-name = "LG-50013A7";
lens-focus = <&vm149c_front>;
port {
ucam_out1: endpoint {
//remote-endpoint = <&mipi_in_ucam0>;
remote-endpoint = <&mipi_in_ucam1>;
data-lanes = <1 2>;
};
};
};
};
&i2c7 {
status = "okay";
icm20602_acc: icm_acc@68 {
compatible = "icm20602_acc";
reg = <0x68>;
irq-gpio = <&gpio0 8 IRQ_TYPE_LEVEL_LOW>; /* GPIO0_B0 */
irq_enable = <0>;
poll_delay_ms = <30>;
type = <SENSOR_TYPE_ACCEL>;
layout = <9>;
};
icm20602_gyro: icm_gyro@68 {
compatible = "icm20602_gyro";
reg = <0x68>;
irq_enable = <0>;
poll_delay_ms = <30>;
type = <SENSOR_TYPE_GYROSCOPE>;
layout = <7>;
};
};
&i2c8 {
status = "okay";
i2c-scl-rising-time-ns = <600>;
i2c-scl-falling-time-ns = <20>;
apds9960@39 {
compatible = "avago,apds9960";
reg = <0x39>;
interrupt-parent = <&gpio3>;
interrupts = <RK_PB2 IRQ_TYPE_LEVEL_LOW>;
led-r-gpio = <&gpio4 24 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&apds_int_l>;
};
bq25703: bq25703@6b {
compatible = "ti,bq25703";
reg = <0x6b>;
extcon = <&fusb0>, <&fusb1>;
interrupt-parent = <&gpio1>;
interrupts = <RK_PC7 IRQ_TYPE_LEVEL_LOW>; /* GPIO1_C7 */
pinctrl-names = "default";
pinctrl-0 = <&charger_ok>;
ti,charge-current = <1500000>;
ti,max-charge-voltage = <8500000>;
ti,max-input-voltage = <20000000>;
ti,max-input-current = <6000000>;
ti,input-current-sdp = <500000>;
ti,input-current-dcp = <2000000>;
ti,input-current-cdp = <2000000>;
ti,input-current-dc = <2000000>;
ti,minimum-sys-voltage = <7400000>;
ti,otg-voltage = <5000000>;
ti,otg-current = <500000>;
ti,input-current = <500000>;
pd-charge-only = <0>;
status = "okay";
};
cw2013: cw2013@62 {
status = "okay";
compatible = "cw201x";
reg = <0x62>;
bat_config_info = <0x15 0x7F 0x6E 0x66 0x65 0x5C 0x5B 0x59
0x58 0x57 0x57 0x54 0x53 0x51 0x4B 0x48
0x40 0x33 0x2A 0x26 0x23 0x25 0x2A 0x34
0x45 0x4F 0x0C 0xCD 0x44 0x68 0x67 0x68
0x6E 0x6F 0x6C 0x68 0x3A 0x10 0x8A 0x01
0x01 0x54 0x52 0x87 0x8F 0x91 0x94 0x52
0x82 0x8C 0x92 0x96 0x82 0xFF 0xFF 0xCB
0x2F 0x7D 0x64 0xA5 0xB5 0x13 0x58 0x09>;
monitor_sec = <5>;
virtual_power = <0>;
divider_res1 = <200>;
divider_res2 = <200>;
dc_det_gpio = <&gpio1 RK_PC7 GPIO_ACTIVE_HIGH>;
};
};
&rk_key {
enter-key {
linux,code = <232>;
label = "enter";
rockchip,adc_value = <170>;
};
};
&pwm3 {
status = "okay";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH 0>;
compatible = "rockchip,remotectl-pwm";
remote_pwm_id = <3>;
handle_cpu_id = <1>;
remote_support_psci = <1>;
pinctrl-names = "default";
pinctrl-0 = <&pwm3b_pin>;
ir_key1 {
rockchip,usercode = <0xff00>;
rockchip,key_table =
<0xeb KEY_POWER>,
<0xec KEY_MENU>,
<0xfc KEY_UP>,
<0xfd KEY_DOWN>,
<0xf1 KEY_LEFT>,
<0xe5 KEY_RIGHT>,
<0xf8 232>,
<0xa7 KEY_VOLUMEDOWN>,
<0xa3 388>, //mouse func
<0xa4 388>, //mouse func
<0xf4 KEY_VOLUMEUP>,
<0xfe KEY_BACK>,
<0xb7 KEY_HOME>;
};
};
&backlight {
pwms = <&pwm1 0 25000 0>;
status = "okay";
};
&pwm1 {
status = "okay";
};
&cdn_dp {
status = "disabled";
};
&dp_in_vopl {
status = "disabled";
};
&dp_in_vopb {
status = "disabled";
};
&hdmi_in_vopl {
status = "okay";
};
&hdmi_in_vopb {
status = "disabled";
};
&route_hdmi {
status = "okay";
connect = <&vopl_out_hdmi>;
};
&vopb {
status = "okay";
assigned-clocks = <&cru DCLK_VOP0_DIV>;
assigned-clock-parents = <&cru PLL_CPLL>;
};
&vopl {
status = "okay";
assigned-clocks = <&cru DCLK_VOP1_DIV>;
assigned-clock-parents = <&cru PLL_VPLL>;
};
&route_edp {
status = "okay";
connect = <&vopb_out_edp>;
};
&edp_in_vopl {
status = "disabled";
};
&edp_in_vopb {
status = "okay";
};
&edp {
force-hpd;
status = "okay";
ports {
edp_out: port@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
edp_out_panel: endpoint@0 {
reg = <0>;
remote-endpoint = <&panel_in_edp>;
};
};
};
};
&i2c2 {
status = "okay";
i2c-scl-rising-time-ns = <600>;
i2c-scl-falling-time-ns = <20>;
ft5336@38 {
compatible = "edt,edt-ft5336", "ft5x06";
reg = <0x38>;
interrupt-parent = <&gpio2>;
interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
reset-gpio = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>; /* GPIO2_A3 */
status = "disabled";
};
};
&pinctrl {
matrix {
matrix_gpio: matrix_gpio {
rockchip,pins =
<0 10 RK_FUNC_GPIO &pcfg_pull_up>,
<0 11 RK_FUNC_GPIO &pcfg_pull_up>,
<0 12 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
apds_int_l: apds-int-l {
rockchip,pins = <3 10 RK_FUNC_GPIO &pcfg_pull_up>;
};
charger {
charger_ok: charge-ok {
rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_up>; /* GPIO1_C7 */
};
};
rt5651 {
rt5651_hpdet: rt5651-hpdet {
rockchip,pins = <1 0 RK_FUNC_GPIO &pcfg_pull_up>; /* GPIO1_A0 */
};
};
};
&mipi_dphy_rx0 {
status = "okay";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
mipi_in_ucam0: endpoint@1 {
reg = <1>;
remote-endpoint = <&ucam_out0>;
data-lanes = <1 2>;
};
};
port@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
dphy_rx0_out: endpoint@0 {
reg = <0>;
remote-endpoint = <&isp0_mipi_in>;
};
};
};
};
&rkisp1_0 {
status = "okay";
port {
#address-cells = <1>;
#size-cells = <0>;
isp0_mipi_in: endpoint@0 {
reg = <0>;
remote-endpoint = <&dphy_rx0_out>;
};
};
};
&mipi_dphy_tx1rx1 {
status = "okay";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
mipi_in_ucam1: endpoint@1 {
reg = <1>;
remote-endpoint = <&ucam_out1>;
data-lanes = <1 2>;
};
};
port@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
dphy_tx1rx1_out: endpoint@0 {
reg = <0>;
remote-endpoint = <&isp1_mipi_in>;
};
};
};
};
&rkisp1_1 {
status = "okay";
port {
#address-cells = <1>;
#size-cells = <0>;
isp1_mipi_in: endpoint@0 {
reg = <0>;
remote-endpoint = <&dphy_tx1rx1_out>;
};
};
};
hlm@Server:/users/hlm/Rockcip_Android10.0_SDK/device/rockchip/rk3399$ git diff
diff --git a/rk3399_Android10/rk3399_Android10.mk b/rk3399_Android10/rk3399_Android10.mk
index 2e4831e..2b2d97a 100755
--- a/rk3399_Android10/rk3399_Android10.mk
+++ b/rk3399_Android10/rk3399_Android10.mk
@@ -51,8 +51,9 @@ PRODUCT_PROPERTY_OVERRIDES += \
persist.vendor.sys.hdmiui=1 \
persist.sys.rotation.einit=3 \
persist.sys.app.rotation=force_land \
- vendor.hwc.device.primary=HDMI-A,DP \
- vendor.hwc.device.extend=DSI
+ vendor.hwc.device.primary=eDP \
+ vendor.hwc.device.extend=HDMI-A
Hi Goenjoy-
I tried your latest files with a new screen and cable and it doesn’t boot - here is the log:
Thanks in advance for taking a look at it. I reset the HEAD back to origin and confirmed that I could build Android 10 and boot on HDMI. That worked fine. Then I made the changes above and got that boot log.
@BarryS Your answer is late. After today, I’m going to have two weeks off. Is there any display on EDP screen?
@BarryS Today, I came back from my holiday to work. Now I can light up the screen you sent me.
Only the following modifications are needed:
1 file changed, 22 insertions(+), 18 deletions(-)
hlm@Server:/users/hlm/Rockcip_Android10.0_SDK/kernel$ git diff
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge-android.dts b/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge-android.dts
index 1762651..5a009a0 100755
--- a/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge-android.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge-android.dts
@@ -27,7 +27,7 @@
};
edp_panel: edp-panel {
- compatible = "panel-simple";
+ compatible = "simple-panel";
backlight = <&backlight>;
bus-format = <MEDIA_BUS_FMT_RGB888_1X24>;
hlm@Server:/users/hlm/Rockcip_Android10.0_SDK/device/rockchip/rk3399$ git diff
diff --git a/rk3399_Android10/rk3399_Android10.mk b/rk3399_Android10/rk3399_Android10.mk
index 9a1272b..30f7bc6 100755
--- a/rk3399_Android10/rk3399_Android10.mk
+++ b/rk3399_Android10/rk3399_Android10.mk
@@ -49,11 +49,11 @@ PRODUCT_PROPERTY_OVERRIDES += \
PRODUCT_PROPERTY_OVERRIDES += \
persist.sys.rotation.efull=true \
persist.vendor.sys.hdmiui=1 \
- persist.sys.rotation.einit=3 \
+ persist.sys.rotation.einit=0 \