板子自带的以太网口无法DHCP得到IP地址，手动设置IP地址也无法Ping通
安卓和Ubuntu固件都使用过，都不行。Ubuntu固件用的是VIM3_Ubuntu-server-bionic_Linux-4.9_arm64_EMMC_V20191231，安卓固件用的是VIM3_Pie_V200319
ZhangChenkai 你好，帮忙看下：
- ifconfig之后有识别到网卡吗？
- 帮忙板子正，反面拍个清晰点的相片看下，特别是网口座，网口芯片附近的器件
- VIM3_Pie_V200319 这个固件插网线后开机启动的完整Log能发出来吗，谢谢。
Hi ZhangChenkai
帮忙发一下串口打印信息：
- VIM3_Pie_V200319 这个固件插网线后开机启动
- 开机启动后，网线插拔一下的打印信息
- 发送ifconfig指令后的打印信息
谢谢了
ifconfig信息
console:/ # ifconfig
wlan0 Link encap:Ethernet HWaddr 18:93:7f:aa:b4:d6 Driver bcmsdh_sdmmc
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 TX bytes:188
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope: Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:71 errors:0 dropped:0 overruns:0 frame:0
TX packets:71 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:11487 TX bytes:11487
eth0 Link encap:Ethernet HWaddr c8:63:14:70:cf:6f Driver meson6-dwmac
inet6 addr: fe80::19c7:9cde:acaa:b7e2/64 Scope: Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:37 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 TX bytes:8630
Interrupt:29
拔网线
[ 189.138377@1] meson6-dwmac ff3f0000.ethernet eth0: Link is Down
[ 189.138805@1] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
插网线
[ 46.906187@0] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 46.909220@0] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 46.916954@0] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 62.649807@0] fb: mem_free_work, free memory: addr:800000
[ 8.341243@4] sensor bsp init
[ 8.341250@4] soc_sensor_probe@soc_sensor.c:551 GENERIC(ERR) :register v4l2 sensor device. result 0, sd 0xbf402410 sd->dev 0xee2c9210
[ 8.418948@4] arm_isp ff140000.isp: assigned reserved memory node linux,isp_cma
[ 8.418965@4] AM_SC: am_sc_parse_dt: rs idx info: name: isp_sc
[ 8.418976@4] AM_SC: am_sc_parse_dt:rs info: irq: 73
[ 8.424136@0] interrupt comes in (irq = 74) without app handler, status: 0x200, pusle mode:0
[ 8.448431@4] acamera_fw_init@acamera_fw.c:104 GENERIC(CRIT) :seamless:0
[ 8.448443@4] pwr_enable: get_named_gpio power-enable fail
[ 8.448444@4] set power fail
[ 8.449239@4] isp init clock is 24 MHZ
[ 8.449269@4] reset init
[ 8.490931@2] arm_sensor_i2c_probe: start to probe
[ 8.490934@2] arm_sensor_i2c_probe:arm isp slave addr 0x6c, rtn 0
[ 8.490935@2] arm_sensor_i2c_probe:arm reg_addr_type 2, rtn 0
[ 8.490936@2] arm_sensor_i2c_probe:arm reg_data_type 1, rtn 0
[ 8.490981@2] arm_sensor_i2c_probe: success get link device:phy-csi
[ 8.490990@2] AM_MIPI: am_mipi_parse_dt: rs idx 0 info: name: csi2_phy0
[ 8.491031@2] AM_MIPI: am_mipi_parse_dt: rs idx 1 info: name: csi2_phy1
[ 8.491036@2] AM_MIPI: am_mipi_parse_dt: rs idx 2 info: name: aphy_reg
[ 8.491043@2] AM_MIPI: am_mipi_parse_dt: rs idx 3 info: name: csi0_host
[ 8.491046@2] AM_MIPI: am_mipi_parse_dt: rs idx 4 info: name: csi1_host
[ 8.491059@2] AM_MIPI: am_mipi_parse_dt: rs idx 0 info: irq 76
[ 8.491064@2] AM_MIPI: am_mipi_parse_dt: rs idx 1 info: irq 77
[ 8.491080@2] AM_MIPI: am_mipi_parse_dt:Success to get link device: isp-adapter
[ 8.491085@2] AM_ADAP: am_adap_parse_dt: rs idx info: name: adapter
[ 8.491092@2] AM_ADAP: am_adap_parse_dt:rs info: irq: 75
[ 8.491141@2] platform ff650000.isp-adapter: assigned reserved memory node linux,adapt_cma
[ 8.491142@2] AM_ADAP: adapter alloc 48M memory
[ 8.491203@2] system_i2c_init:success to add i2c driver
[ 8.491625@4] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 8.491630@4] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 8.492037@4] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 8.492040@4] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 8.492452@4] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 8.492455@4] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 8.492457@4] sensor_get_id@OV08a10_drv.c:380 GENERIC(ERR) :sensor_get_id: Failed to read sensor id
[ 8.492458@4]
[ 8.494677@4] sensor_init_ov08a10@OV08a10_drv.c:711 GENERIC(ERR) :sensor_init_ov08a10: Success subdev init
[ 8.494678@4]
[ 8.494680@4] camera_init@soc_sensor.c:229 GENERIC(INFO) :Sensor has been initialized for ctx:0
[ 8.494681@4]
[ 8.494686@4] camera_ioctl@soc_sensor.c:447 GENERIC(ERR) :get isp_seq_num = 0
[ 8.494687@4]
[ 8.515312@4] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 8.515315@4] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 8.515720@4] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 8.515722@4] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 8.516131@3] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 8.516135@3] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 8.516137@3] sensor_get_id@OV08a10_drv.c:380 GENERIC(ERR) :sensor_get_id: Failed to read sensor id
[ 8.516138@3]
[ 8.516141@3] camera_ioctl@soc_sensor.c:447 GENERIC(ERR) :get isp_seq_num = 0
[ 8.516142@3]
[ 8.516218@3] get_calibrations_v4l2@acamera_get_calibrations_v4l2.c:31 GENERIC(CRIT) :Request calibration ctx_id:0 sensor_arg:0xbf46a6a0 from soc_iq device ret 0
[ 8.517700@3] general_set_wdr_mode@general_func.c:456 GENERAL(CRIT) :Setting Linear Binary Sequence
[ 8.517701@3]
[ 8.518018@4] sbuf_mgr_alloc_sbuf@sbuf_func.c:175 SBUF(CRIT) :sbuf: len_needed: 234096, len_alloc: 241663, len_used: 237568, page_size: 4096, buf_alloc: ebd40000, buf_used: ebd40000.
[ 8.518038@4] sbuf_calibration_init@sbuf_func.c:493 SBUF(CRIT) :sbuf_calibration wdr_mode updated: 65535 -> 0.
[ 8.519517@3] acamera_3aalg_preset@acamera_fw.c:628 GENERIC(CRIT) :Enter Linear Binary Preset
[ 8.522538@2] connection_thread@main_firmware.c:102 GENERIC(CRIT) :connection_thread start
[ 8.522595@2] isp_fw_process@main_firmware.c:120 GENERIC(CRIT) :isp_fw_process start
[ 8.523021@2] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 8.523025@2] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 8.523438@3] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 8.523441@3] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 8.523850@2] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 8.523853@2] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 8.523856@2] sensor_get_id@OV08a10_drv.c:380 GENERIC(ERR) :sensor_get_id: Failed to read sensor id
[ 8.523856@2]
[ 8.524059@2] isp_fw_do_set_exposure_auto@fw-interface.c:1281 GENERIC(CRIT) :AE_MODE_ID = 47
[ 8.541263@3] logd.daemon: reinit
[ 8.744876@1] healthd: BatteryTemperaturePath not found
[ 8.744884@1] healthd: BatteryCycleCountPath not found
[ 8.752587@4] android.hardware.health@2.0-impl: wakealarm_init: timerfd_create failed
[ 8.753237@4] healthd: battery l=42 v=4 t=42.4 h=2 st=2 c=1 fc=10000000 chg=u
[ 8.761628@1] hdmitx: system: set hdcp_pwr 1
[ 8.801693@0] unifykey: amlkey_init_gen() enter!
[ 8.802900@3] hdmitx: system: restore hdcp_pwr 0
[ 8.835002@1] hdmitx: system: sname = 1080p60hz
[ 8.835006@1] hdmitx: system: char_clk = 148500
[ 8.835007@1] hdmitx: system: cd = 4
[ 8.835009@1] hdmitx: system: cs = 2
[ 8.835012@1] hdmitx: RX tmds clk: 150 Calc clk: 148
[ 8.875980@2] emmc_key_read:114, read ok
[ 8.875991@2] unifykey: amlkey_init_gen() storagekey_info.buffer=c5080000, storagekey_info.size = 40000!
[ 8.903269@0] audit: audit_lost=1 audit_rate_limit=5 audit_backlog_limit=64
[ 8.903272@0] audit: rate limit exceeded
[ 8.903390@0] fb: osd_open, 1497, fb_index=0,fb_rmem_size=26738688
[ 8.903519@0] fb: osd_open, 1497, fb_index=1,fb_rmem_size=1048576
[ 8.903552@0] fb: osd_open, 1497, fb_index=2,fb_rmem_size=1048576
[ 8.903554@3] vout: vout_io_open
[ 8.903734@0] fb: vpu clkc clock is 199 MHZ
[ 8.903749@0] fb: osd_open, 1497, fb_index=3,fb_rmem_size=8388608
[ 8.905177@3] vfm_map_store:rm default
[ 8.905284@3] vfm_map_store:add default decoder ppmgr deinterlace amvideo
[ 8.911015@3] file system registered
[ 8.916568@3] assign_ffs_buffer FFS_BUFFER_MAX=100!!!
[ 8.948228@3] [DI] load 0x3e00 pq table len 424 later.
[ 9.113162@0] vout: vout_io_open
[ 9.113169@0] vout: vout_ioctl: cmd_dir = 0x2, cmd_nr = 0x0
[ 9.113174@0] vout: vout_io_release
[ 9.231967@2] cectx ff80023c.aocec: init_cec_port_info phy_addr:1000, port num:1
[ 9.231969@2] cectx ff80023c.aocec: port_seq=0x0
[ 9.231972@2] cectx ff80023c.aocec: portinfo id:0 arc:0 phy:1100,type:0
[ 9.266617@4] aml_tdm_open
[ 9.267146@4] loopback_dai_startup
[ 9.267393@2] loopback_dai_shutdown
[ 9.267602@4] aml_spdif_open
[ 9.267824@2] aml_spdif_close
[ 9.267974@2] aml_tdm_open
[ 9.268694@3] aml_tdm_open
[ 9.295887@5] type=1400 audit(1293883481.000:12): avc: denied { setattr } for pid=2567 comm=“init” name=“log” dev=“mmcblk0p20” ino=259598 scontext=u:r:vendor_init:s0 tcontext=u:object_r:log_file:s0 tclass=dir permissive=1
[ 9.315305@5] type=1400 audit(1293883481.004:13): avc: denied { setattr } for pid=2567 comm=“init” name=“media” dev=“mmcblk0p20” ino=259595 scontext=u:r:vendor_init:s0 tcontext=u:object_r:media_rw_data_file:s0 tclass=dir permissive=1
[ 9.336047@5] type=1400 audit(1293883481.004:13): avc: denied { setattr } for pid=2567 comm=“init” name=“media” dev=“mmcblk0p20” ino=259595 scontext=u:r:vendor_init:s0 tcontext=u:object_r:media_rw_data_file:s0 tclass=dir permissive=1
[ 9.356599@5] type=1400 audit(1293883481.512:14): avc: denied { read } for pid=3350 comm=“systemcontrol” name=“u:object_r:system_prop:s0” dev=“tmpfs” ino=2361 scontext=u:r:system_control:s0 tcontext=u:object_r:system_prop:s0 tclass=file permissive=1
console:/ $ [ 9.415917@0] read descriptors
[ 9.415985@0] read strings
[ 9.884406@5] avc open
[ 9.884428@5] amvenc_avc check CMA pool success, max instance: 3.
[ 9.888372@3] allocating phys 0x5a400000, size 20480k, wq:eaf9a800.
[ 9.893594@3] amvenc_avc memory config success, buff start:0x5a400000, size is 0x1400000, wq:eaf9a800.
[ 9.903041@3] avc release, wq:eaf9a800
[ 9.906657@3] remove encode_work_queue eaf9a800 success, _destroy_encode_work_queue line 3513.
[ 9.915635@3] [+] vpu_open
[ 9.919256@2] allocating phys 0x5a400000, virt addr 0x0, size 65536k
[ 9.924477@2] [-] vpu_open, ret: 0
[ 9.927725@2] vpu_release
[ 9.930292@2] vpu_free_buffers
[ 9.933303@2] vpu_free_instances
[ 9.936534@2] vpu_release, s_video_memory 0x5a400000
[ 10.470307@0] fb: osd[0] enable: 1 scale:0x10001 (composer@2.2-se)
[ 10.470847@0] fb: osd[0] enable: 1 scale:0x10001 (composer@2.2-se)
[ 10.477887@0] fb: free_scale_switch to fb0, mode: 0x10001
[ 10.482492@0] fb: set logo loaded
[ 10.885567@2] capability: warning: `main’ uses 32-bit capabilities (legacy support in use)
[ 11.736305@4] early_suspend_state=0
[ 12.251072@2] healthd: battery l=42 v=4 t=42.4 h=2 st=2 c=1 fc=10000000 chg=u
[ 12.253282@2] healthd: battery l=42 v=4 t=42.4 h=2 st=2 c=1 fc=10000000 chg=u
[ 12.305782@0] healthd: battery l=42 v=4 t=42.4 h=2 st=2 c=1 fc=10000000 chg=u
[ 12.306032@2] vout: aml_tvout_mode_work: monitor_timeout
[ 12.823501@0] cectx ff80023c.aocec: init_cec_port_info phy_addr:1000, port num:1
[ 12.825265@0] cectx ff80023c.aocec: port_seq=0x0
[ 12.830049@0] cectx ff80023c.aocec: portinfo id:0 arc:0 phy:1100,type:0
[ 13.023109@1] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP.
[ 13.025788@1] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.091207@3] sdcardfs version 2.0
[ 13.091236@3] sdcardfs: dev_name -> /data/media
[ 13.094359@3] sdcardfs: options -> fsuid=1023,fsgid=1023,multiuser,derive_gid,default_normal,mask=6,userid=0,gid=1015
[ 13.104179@3] sdcardfs: mnt -> ea8cf510
[ 13.108272@3] sdcardfs: mounted on top of /data/media type ext4
[ 13.115298@3] Remount options were mask=23,gid=9997 for vfsmnt ea8cf910.
[ 13.121578@3] sdcardfs : options - debug:1
[ 13.124550@3] sdcardfs : options - gid:9997
[ 13.132264@3] sdcardfs : options - mask:23
[ 13.133182@3] Remount options were mask=7,gid=9997 for vfsmnt eb6f5810.
[ 13.139831@3] sdcardfs : options - debug:1
[ 13.145284@3] sdcardfs : options - gid:9997
[ 13.147624@3] sdcardfs : options - mask:7
[ 13.518228@4] aml_wifi wifi: [usb_power_control] Set WiFi power down
[ 13.696274@2] BT_RADIO going: on
[ 13.696300@2] AML_BT: going ON
[ 13.726982@5] aml_wifi wifi: [usb_power_control] Set WiFi power on !
[ 13.728915@0] meson-mmc: sdio: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 13.734288@0] meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8
[ 13.742231@0] meson-mmc: sdio: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 13.747281@0] meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8
[ 13.758588@0] meson-mmc: sdio: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 13.760286@0] meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8
[ 13.774923@5] meson-mmc: actual_clock :0, HHI_nand: 0x80
[ 13.774953@5] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 13.804204@5] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 13.804306@5] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 13.841676@5] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 13.844502@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 13.849653@5] init: Could not find service hosting interface android.hardware.radio@1.0::IRadio/slot1
[ 13.857466@5] init: Could not find service hosting interface android.hardware.radio@1.0::IRadio/slot1
[ 13.865815@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 13.876342@5] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 13.883318@5] sdio: queuing unknown CIS tuple 0x81 (9 bytes)
[ 14.006227@5] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
[ 14.010798@5] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
[ 14.016395@5] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
[ 14.023389@5] meson-mmc: Data 1 aligned delay is 0
[ 14.028150@5] meson-mmc: sdio: clk 199999997 tuning start
[ 14.033560@5] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 14.044000@5] meson-mmc: sdio: rx_tuning_result[1] = 40
[ 14.049381@5] meson-mmc: sdio: rx_tuning_result[2] = 40
[ 14.056665@5] meson-mmc: sdio: rx_tuning_result[3] = 40
[ 14.058736@5] meson-mmc: sdio: rx_tuning_result[4] = 40
[ 14.061456@5] meson-mmc: sdio: best_win_start =1, best_win_size =4
[ 14.067708@5] meson-mmc: sdio: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x32000
[ 14.084236@5] sdio: new ultra high speed SDR104 SDIO card at address 0001
[ 14.085397@5] sdio: clock 199999997, 4-bit-bus-width
[ 14.091088@3] meson-mmc: [sdio_reinit] finish
[ 14.094817@3] aml_wifi wifi: [usb_power_control] Set WiFi power on !
[ 14.110466@1] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600
[ 14.112927@1] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 9600
[ 14.121246@0] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200
[ 14.134296@2] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 115200 to 2000000
[ 14.303893@3] aml_wifi wifi: [pci_reinit] pci wifi reinit!
[ 14.303925@3] aml_wifi wifi: [wifi_power_ioctl] Set sdio wifi power up!
[ 14.310455@3] aml_wifi wifi: [wifi_power_ioctl] wifi interface dev type: sdio, length = 4
[ 14.341423@5] dhd_module_init: in Dongle Host Driver, version 100.10.315.3 (r771911)
[ 14.343691@5] ======== dhd_wlan_init_plat_data ========
[ 14.348823@5] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=85, oob_irq_flags=0x418
[ 14.356309@5] dhd_wlan_init_gpio: WL_REG_ON=-1
[ 14.360819@5] dhd_wifi_platform_load: Enter
[ 14.364918@5] Power-up adapter ‘DHD generic adapter’
[ 14.369833@5] wifi_platform_set_power = 1
[ 14.373791@5] ======== PULL WL_REG_ON(-1) HIGH! ========
[ 14.379104@5] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 482
[ 14.581958@4] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 2000000 to 115200
[ 14.585864@5] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 482
[ 14.789740@4] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 115200 to 2000000
[ 15.098059@5] wifi_platform_bus_enumerate device present 1
[ 15.098090@5] ======== Card detection to detect SDIO card! ========
[ 15.104305@5] sdio_reset_comm():
[ 15.107424@5] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
[ 15.117165@5] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
[ 15.123548@5] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
[ 15.133115@5] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
[ 15.139928@5] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
[ 15.145933@5] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
[ 15.153938@5] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 15.158519@5] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 15.168910@3] meson-mmc: actual_clock :0, HHI_nand: 0x80
[ 15.171048@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 15.194098@3] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 15.194205@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 15.223873@1] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 15.227020@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 15.232841@5] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 15.240476@0] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 15.250780@0] sdio: queuing unknown CIS tuple 0x81 (9 bytes)
[ 15.353767@5] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
[ 15.357883@5] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
[ 15.364286@5] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
[ 15.371202@5] meson-mmc: Data 1 aligned delay is 0
[ 15.375668@5] meson-mmc: sdio: clk 199999997 tuning start
[ 15.381129@1] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 15.391298@5] meson-mmc: sdio: rx_tuning_result[1] = 40
[ 15.395593@5] meson-mmc: sdio: rx_tuning_result[2] = 40
[ 15.401371@2] meson-mmc: sdio: rx_tuning_result[3] = 40
[ 15.405860@0] meson-mmc: sdio: rx_tuning_result[4] = 40
[ 15.409078@2] meson-mmc: sdio: best_win_start =1, best_win_size =4
[ 15.415206@2] meson-mmc: sdio: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x32000
[ 15.423627@2] meson-mmc: [sdio_reinit] finish
[ 15.445080@0] bcmsdh_sdmmc_probe: Enter num=1
[ 15.445316@0] bcmsdh_sdmmc_probe: Enter num=2
[ 15.448371@0] bus num (host idx)=2, slot num (rca)=1
[ 15.453527@2] found adapter info ‘DHD generic adapter’
[ 15.459136@2] Wifi: bcmdhd_mem_prealloc: sectoin 3, size 139264
[ 15.464199@2] succeed to alloc static buf
[ 15.468338@2] Wifi: bcmdhd_mem_prealloc: sectoin 4, size 0
[ 15.474281@0] sdioh_attach: set sd_f2_blocksize 256
[ 15.478703@0] sdioh_attach: sd clock rate = 0
[ 15.483504@0] dhdsdio_probe : no mutex held. set lock
[ 15.488432@0] F1 signature read @0x18000000=0x17294359
[ 15.498193@0] F1 signature OK, socitype:0x1 chip:0x4359 rev:0x9 pkg:0x2
[ 15.501186@0] DHD: dongle ram size is set to 917504(orig 917504) at 0x160000
[ 15.506664@3] Wifi: bcmdhd_mem_prealloc: sectoin 7, size 24928
[ 15.512333@3] dhd_conf_set_chiprev: chip=0x4359, chiprev=9
[ 15.518638@3] Wifi: bcmdhd_mem_prealloc: sectoin 0, size 10320
[ 15.524569@3] Wifi: bcmdhd_mem_prealloc: sectoin 5, size 65536
[ 15.529747@3] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 15.537286@3] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 15.545144@5] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 15.553044@5] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 15.560916@5] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 15.568818@5] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 15.576689@5] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 15.584602@5] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 15.592461@5] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 15.600371@5] wl_escan_attach: Enter
[ 15.603927@5] Wifi: bcmdhd_mem_prealloc: sectoin 19, size 67244
[ 15.609826@5] wl_escan_init: Enter
[ 15.613448@0] wl_create_event_handler(): thread:wl_escan_handler:fef started
[ 15.613452@3] tsk Enter, tsk = 0xed4d0160
[ 15.624351@2] Wifi: bcmdhd_mem_prealloc: sectoin 20, size 262144
[ 15.630873@4] Wifi: bcmdhd_mem_prealloc: sectoin 22, size 65536
[ 15.636253@0] dhd_attach(): thread:dhd_watchdog_thread:ff0 started
[ 15.642350@0] dhd_attach(): thread:dhd_dpc:ff1 started
[ 15.647941@1] dhd_attach(): thread:dhd_rxf:ff2 started
[ 15.652497@4] dhd_deferred_work_init: work queue initialized
[ 15.658110@4] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2
[ 15.664785@4] dhd_get_memdump_info: MEMDUMP ENABLED = 0
[ 15.670236@4] Wifi: bcmdhd_mem_prealloc: sectoin 1, size 10300
[ 15.675762@4] Wifi: bcmdhd_mem_prealloc: sectoin 2, size 65536
[ 15.682137@4] sdioh_cis_read: func_cis_ptr[0]=0x10ac
[ 15.714245@3] Dongle Host Driver, version 100.10.315.3 (r771911)
[ 15.715270@3] ANDROID-MSG) wl_ext_iapsta_attach_netdev: ifidx=0, bssidx=0
[ 15.721419@3] Register interface [wlan0] MAC: 18:93:7f:aa:b4:d6
[ 15.721419@3]
[ 15.729177@5] dhd_dbg_detach_pkt_monitor, 1914
[ 15.733504@5] dhd_bus_devreset: == Power OFF ==
[ 15.738471@1] dhd_txglom_enable: enable 0
[ 15.741914@1] dhd_conf_set_txglom_params: txglom_mode=copy
[ 15.747506@3] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0
[ 15.754191@3] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1
[ 15.761136@3] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300
[ 15.768137@3] dhd_bus_devreset: WLAN OFF DONE
[ 15.772638@1] wifi_platform_set_power = 0
[ 15.776540@1] ======== PULL WL_REG_ON(-1) LOW! ========
[ 15.781772@1] wl_escan_deinit: Enter
[ 15.785292@2] wl_destroy_event_handler(): thread:wl_escan_handler:fef wait for terminate
[ 15.785296@4] wl_escan_event_handler: was terminated
[ 15.798312@2] wl_destroy_event_handler(): thread:wl_escan_handler:fef terminated OK
[ 15.805949@2] dhdsdio_probe : the lock is released.
[ 15.810903@2] dhd_module_init: Exit err=0
[ 15.901304@3] dhd_open: Enter ea587000
[ 15.901328@3] dhd_open : no mutex held. set lock
[ 15.904085@3]
[ 15.904085@3] Dongle Host Driver, version 100.10.315.3 (r771911)
[ 15.911669@3] ANDROID-MSG) wl_ext_iapsta_attach_netdev: ifidx=0, bssidx=0
[ 15.918431@3] wl_android_wifi_on in 1
[ 15.922118@3] wl_android_wifi_on in 2: g_wifi_on=0
[ 15.926854@3] wifi_platform_set_power = 1
[ 15.930811@3] ======== PULL WL_REG_ON(-1) HIGH! ========
[ 15.938539@3] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 482
[ 16.142779@3] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 482
[ 16.650106@3] sdio_reset_comm():
[ 16.650195@3] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
[ 16.657646@3] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
[ 16.663495@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
[ 16.674818@2] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
[ 16.680156@2] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
[ 16.686491@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
[ 16.694538@2] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 16.699408@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 16.709769@1] meson-mmc: actual_clock :0, HHI_nand: 0x80
[ 16.711234@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 16.742065@3] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 16.742168@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 16.891333@0] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
[ 16.896017@2] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
[ 16.901485@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
[ 16.908477@2] meson-mmc: Data 1 aligned delay is 0
[ 16.913244@2] meson-mmc: sdio: clk 199999997 tuning start
[ 16.918668@2] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 16.927393@2] meson-mmc: sdio: rx_tuning_result[1] = 40
[ 16.932487@2] meson-mmc: sdio: rx_tuning_result[2] = 40
[ 16.938518@4] meson-mmc: sdio: rx_tuning_result[3] = 40
[ 16.942456@2] meson-mmc: sdio: rx_tuning_result[4] = 40
[ 16.946581@2] meson-mmc: sdio: best_win_start =1, best_win_size =4
[ 16.953045@2] meson-mmc: sdio: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x32000
[ 16.962845@5] sdioh_start: set sd_f2_blocksize 256
[ 16.966550@2]
[ 16.966550@2]
[ 16.966550@2] dhd_bus_devreset: == WLAN ON ==
[ 16.973668@2] F1 signature read @0x18000000=0x17294359
[ 16.982853@2] F1 signature OK, socitype:0x1 chip:0x4359 rev:0x9 pkg:0x2
[ 16.985730@2] DHD: dongle ram size is set to 917504(orig 917504) at 0x160000
[ 16.993268@3] dhd_conf_read_config: Ignore config file /vendor/etc/wifi/4359/config.txt
[ 17.000327@3] Final fw_path=/vendor/etc/wifi/4359/fw_bcm4359c0_ag.bin
[ 17.006643@3] Final nv_path=/vendor/etc/wifi/4359/nvram_ap6398s.txt
[ 17.012875@3] Final clm_path=/vendor/etc/wifi/4359/clm.blob
[ 17.018433@3] Final conf_path=/vendor/etc/wifi/4359/config.txt
[ 17.027728@0] dhd_os_open_image1: /vendor/etc/wifi/4359/fw_bcm4359c0_ag.bin (606301 bytes) open success
[ 17.106394@1] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 17.173818@3] dhd_os_open_image1: /vendor/etc/wifi/4359/nvram_ap6398s.txt (5861 bytes) open success
[ 17.177755@3] NVRAM version: AP6398S_NVRAM_V1.1_20170926
[ 17.183722@5] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 17.367139@3] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[ 17.367578@4] si_get_pmu_reg_addr: addrRET: 18000670
[ 17.373191@5] bcmsdh_oob_intr_register: HW_OOB irq=85 flags=0x8
[ 17.378540@5] dhd_get_memdump_info: MEMDUMP ENABLED = 0
[ 17.384112@5] Disable tdls_auto_op failed. -1
[ 17.387924@5] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 1
[ 17.395271@0] dhd_apply_default_clm: Ignore clm file /vendor/etc/wifi/4359/clm.blob
[ 17.404032@2] Firmware up: op_mode=0x0405, MAC=18:93:7f:aa:b4:d6
[ 17.418403@2] Driver: 100.10.315.3 (r771911)
[ 17.418403@2] Firmware: wl0: Jan 2 2019 14:30:52 version 9.87.51.11.25 (ba5357b@shgit) ® FWID 01-b5e1a852
[ 17.418403@2] CLM: 9.7.5
[ 17.430304@5] dhd_txglom_enable: enable 1
[ 17.433987@5] dhd_conf_set_txglom_params: txglom_mode=copy
[ 17.439496@5] dhd_conf_set_txglom_params: txglomsize=36, deferred_tx_len=0
[ 17.446323@5] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1
[ 17.453224@5] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300
[ 17.460263@5] dhd_conf_get_disable_proptx: fw_proptx=0, disable_proptx=1
[ 17.468033@5] dhd_pno_init: Support Android Location Service
[ 17.504103@2] rtt_do_get_ioctl: failed to send getbuf proxd iovar (CMD ID : 1), status=-23
[ 17.506751@2] dhd_rtt_init : FTM is not supported
[ 17.512917@1] failed to set WNM capabilities
[ 17.527126@0] dhd_preinit_ioctls: Failed to get preserve log # !
[ 17.527659@5] dhd_conf_set_country: set country CN, revision 38
[ 17.536190@2] Country code: CN (CN/38)
[ 17.539463@2] CONFIG-ERROR) dhd_conf_set_intiovar: txbf setting failed -23
[ 17.550222@5] wl_android_wifi_on: Success
[ 17.590200@5] wl_escan_init: Enter
[ 17.590396@0] wl_create_event_handler(): thread:wl_escan_handler:ffa started
[ 17.590399@2] tsk Enter, tsk = 0xed4d0160
[ 17.599251@0] dhd_open : the lock is released.
[ 17.604110@0] dhd_open: Exit ret=0
[ 17.607266@1] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.615100@1] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
[ 17.671669@0] P2P interface registered
[ 17.671699@0] wl_cfgp2p_add_p2p_disc_if: wdev: e9c16400, wdev->net: (null)
[ 17.686117@5] WLC_E_IF: NO_IF set, event Ignored
[ 17.749042@3] Random MAC OUI to be used - da:1:19
[ 17.758526@5] dhd_dbg_attach_pkt_monitor, 1316
[ 17.760175@3] net_os_enable_packet_filter: val = 0
[ 17.762873@3] net_os_rxfilter_add_remove: add_remove = 0, num = 2
[ 17.769614@5] net_os_enable_packet_filter: val = 1
[ 17.773458@5] net_os_enable_packet_filter: val = 0
[ 17.778236@5] net_os_rxfilter_add_remove: add_remove = 0, num = 3
[ 17.785117@4] net_os_enable_packet_filter: val = 1
[ 17.789101@4] dhd_set_suspend: Remove extra suspend setting
[ 17.794408@5] dhd_enable_packet_filter: enter, value = 0
[ 20.181599@5] zram0: detected capacity change from 0 to 268435456
[ 20.195427@3] type=1400 audit(1293883485.168:40): avc: denied { getattr } for pid=3576 comm=“android.ui” path="/sys/devices/virtual/amhdmitx/amhdmitx0/hdmi/state" dev=“sysfs” ino=10102 scontext=u:r:system_server:s0 tcontext=u:object_r:sysfs_amhdmitx:s0 tclass=file permissive=1
[ 20.214708@3] type=1400 audit(1293883492.956:41): avc: denied { getattr } for pid=4099 comm=“preinstall.sh” path="/data/local/symbol_thirdpart_apks_installed" dev=“mmcblk0p20” ino=130173 scontext=u:r:preinstall:s0 tcontext=u:object_r:system_data_file:s0 tclass=file permissive=1
[ 20.221368@4] mkswap: Swapspace size: 262140k, UUID=373ec871-f825-4d5b-8a5e-11d2eede83cf
[ 20.239283@5] Adding 262140k swap on /dev/block/zram0. Priority:-1 extents:1 across:262140k SS
[ 20.241613@5] selinux: SELinux: Skipping restorecon_recursive(/data/system_ce/0)
[ 20.241613@5]
[ 20.315502@0] selinux: SELinux: Skipping restorecon_recursive(/data/misc_ce/0)
[ 20.315502@0]
[ 20.523595@2] type=1400 audit(1293883492.956:41): avc: denied { getattr } for pid=4099 comm=“preinstall.sh” path="/data/local/symbol_thirdpart_apks_installed" dev=“mmcblk0p20” ino=130173 scontext=u:r:preinstall:s0 tcontext=u:object_r:system_data_file:s0 tclass=file permissive=1
[ 20.542733@2] type=1400 audit(1293883493.284:42): avc: denied { read } for pid=4118 comm=“screencontrol” name=“vndbinder” dev=“tmpfs” ino=2454 scontext=u:r:screen_control:s0 tcontext=u:object_r:vndbinder_device:s0 tclass=chr_file permissive=1
[ 20.564364@2] type=1400 audit(1293883493.284:42): avc: denied { read } for pid=4118 comm=“screencontrol” name=“vndbinder” dev=“tmpfs” ino=2454 scontext=u:r:screen_control:s0 tcontext=u:object_r:vndbinder_device:s0 tclass=chr_file permissive=1
[ 20.586348@2] type=1400 audit(1293883493.284:43): avc: denied { write } for pid=4118 comm=“screencontrol” name=“vndbinder” dev=“tmpfs” ino=2454 scontext=u:r:screen_control:s0 tcontext=u:object_r:vndbinder_device:s0 tclass=chr_file permissive=1
[ 20.608152@2] type=1400 audit(1293883493.284:43): avc: denied { write } for pid=4118 comm=“screencontrol” name=“vndbinder” dev=“tmpfs” ino=2454 scontext=u:r:screen_control:s0 tcontext=u:object_r:vndbinder_device:s0 tclass=chr_file permissive=1
[ 20.628904@2] type=1400 audit(1293883493.284:44): avc: denied { open } for pid=4118 comm=“screencontrol” path="/dev/vndbinder" dev=“tmpfs” ino=2454 scontext=u:r:screen_control:s0 tcontext=u:object_r:vndbinder_device:s0 tclass=chr_file permissive=1
[ 20.655489@5] type=1400 audit(1293883493.284:44): avc: denied { open } for pid=4118 comm=“screencontrol” path="/dev/vndbinder" dev=“tmpfs” ino=2454 scontext=u:r:screen_control:s0 tcontext=u:object_r:vndbinder_device:s0 tclass=chr_file permissive=1
[ 20.672669@5] type=1400 audit(1293883493.284:45): avc: denied { ioctl } for pid=4118 comm=“screencontrol” path="/dev/vndbinder" dev=“tmpfs” ino=2454 ioctlcmd=0x6209 scontext=u:r:screen_control:s0 tcontext=u:object_r:vndbinder_device:s0 tclass=chr_file permissive=1
[ 20.741263@5] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 0, bssidx: 0
[ 21.753571@4] audio_dsp: dts_dec_control/0x0
[ 21.762998@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 21.763626@3] audio_dsp: last mode 0,now 0
[ 21.937025@0] audio_dsp: drc high cut scale set to 100%
[ 21.937601@2] audio_dsp: drc low boost scale set to 100%
[ 21.944451@3] audio_dsp: drc mode set to LINE
[ 21.970083@3] [wlan0] wl_escan_handler : SCAN COMPLETED: scanned AP count=13
[ 22.979556@4] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 22.980185@4] audio_dsp: last mode 0,now 0
[ 23.032721@3] audio_dsp: IEC958_mode_codec= 0, IEC958 type 2 CH PCM
[ 23.033346@3] audio_dsp: last mode 0,now 0
Hi ZhangChengkai
感谢你的帮忙
- 留意到有TX,没有RX，你那边有万用表吗，能否帮忙看一下R108两端是否阻值为22R？
RX bytes:0 TX bytes:8630
- 查看下接网口那端的座子是否有变型？
如果这两个都是正常的话，麻烦板子退回给我们这边售后，会尽快安排修复好给你。
2 Likes
感谢回答。
阻值是22欧，网口端子也没有变形。已经寄出售后。
ZhangChenkai 你好，设备已经检修完成，今天会寄回去给你。
原因：网口功能的RX有个数据脚虚焊了，目前已修复好，并做了全功能测试、老化测试、外观清洁。老化测试用了两天时间以确保设备没有问题，所以要今天才能给你寄回去。
抱歉给您添麻烦了，感谢您的支持与帮助。
2 Likes