板子之前一直是接着LCD,今天把LCD拔了装上外壳，发现启动不了，停在了uboot, 把LCD重新接上又正常了。下面是Log
U-Boot 2015.01-g7331386-dirty (Jan 02 2020 - 11:48:33)
DRAM: 3.8 GiB
Relocation Offset is: d6e22000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 00000000d7f28390
aml_i2c_init_port init regs for 0
NAND: get_sys_clk_rate_mtd() 290, clock setting 200!
NAND device id: 0 bf ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 290, clock setting 200!
NAND device id: 0 bf ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC: aml_priv->desc_buf = 0x00000000d3e12a70
aml_priv->desc_buf = 0x00000000d3e14db0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x1, tx-dly 0, clock 40000000
aml_sd_retry_refix[983]:delay = 0x0,gadjust =0x2000
[mmc_startup] mmc refix success
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
start dts,buffer=00000000d3e17620,dt_addr=00000000d3e17620
get_partition_from_dts() 91: ret 0
parts: 17
00: logo 0000000000800000 1
01: recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dtbo 0000000000800000 1
04: cri_data 0000000000800000 2
05: param 0000000001000000 2
06: boot 0000000001000000 1
set has_boot_slot = 0
07: rsv 0000000001000000 1
08: metadata 0000000001000000 1
09: vbmeta 0000000000200000 1
10: tee 0000000002000000 1
11: vendor 0000000014000000 1
12: odm 0000000008000000 1
13: system 0000000050000000 1
14: product 0000000008000000 1
15: cache 0000000046000000 2
16: data ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x4d400000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3477: calc c82a6739, store c82a6739
_verify_dtb_checksum()-3477: calc c82a6739, store c82a6739
dtb_read()-3694: total valid 2
update_old_dtb()-3675: do nothing
aml_i2c_init_port init regs for 0
fusb302_init: Device ID: 0x91
CC connected in 0 as UFP
fusb302 detect chip.port_num = 0
amlkey_init() enter!
[EFUSE_MSG]keynum is 1
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv…
cvbs: cpuid:0x29
LCD_RESET PIN: 0
lcd: detect mode: tablet, key_valid: 0
lcd: detect lcd_clk_path: 1
lcd: failed to get lcd_cpu_gpio_names
lcd: load config from dts
lcd: pinctrl_version: 2
lcd: use panel_type=lcd_1
lcd: bl: pinctrl_version: 2
lcd: bl: name: backlight_pwm, method: 1
lcd: bl: pwm_reg=0x00800002
lcd: error: gpio: wrong name invalid
lcd: bl: aml_bl_power_ctrl: 0
Net: __phy_realtek_initdwmac.ff3f0000amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 1
MACADDR:02:00:00:06:17:01(from chipid)
CONFIG_AVB2: null
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode:::: cold_boot
lcd: error: outputmode[1080p60hz] is not support
hpd_state=1
edid preferred_mode is 576p50hz[18]
hdr mode is 0
dv mode is ver:0 len: 0
hdr10+ mode is 0
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[CANVAS]canvas init
[CANVAS]addr=0x7fbf4800 width=2176, height=3840