DIY Case/Housing for VIMs

Hello, I am taking in charge for this. I will message to you on aliexpress right now. Thank you and sorry for the mistake.

1 Like

Thanks Willow, appreciated

. :+1:

Used two cases and some VIM original case pieces to enclose the VIM2 + the mounted Tone board. I installed a few holes to help with ventilation. :slight_smile:

Hit a snag with the cutoff wheel and removed more material from the rear of the top section than I had intended. It is a thing like that, that caused me two order two of the clear cases to begin with.:rofl:

I will use different feet when I get some 40mm screws. The 45mm screws I’m using now are too long, I did not want to cut them.

5 Likes

hello

what temperature and best for vim2 max

speed fan 1, it is a 45 to 52 °, when I watch video or iptv.

I put small wedges to raise the lid, the hot air escapes better.!

KHADAS%201|375x500

4 Likes

Hi willow

Package containing the GPIO cover arrived safely. Thanks again…

Hello All …

Anything in project regarding VTV and TONE boards cases ?
It’ll be great modular integration look :wink:

By all

https://www.audiophonics.fr/en/aluminium-boxes-cases/aluminum-case-for-khadas-tone-board-p-13626.html

2 Likes

Oo that’s smart! Okay we shall take note of that for future casing designs.

The 3705 cooling fan (Edge project) and New VIM Heatsink will solve this issue by flipping the air flow in the opposite direction, so that hot air can exit through the button gaps.

hello

we must think of dismantling it and cleaning it with all the dust, like a computer.
I noticed under the fan, the fins etc, small brush very flexible.
what is the optimum operating temperature of s912?

thank you

5 Likes

Creative! I like that exhaust manifold.

@fred21 interesting that you placed the tape there, does it reduce the air noise?

In simulations, I found that covering the gap between the fan and heatsink, also improved the cooling efficiency.

Also, is that tape on the fins themselves? Or is that some shiny aluminium sheet?

yes reduces the noise. sticky aluminum foil.
video, in auto adjustment of the fan between 50 and 55 °.

2 Likes

Hello
You should try 4 small joints at this location

1 Like

Hey @fred21 which location? Sorry don’t quite get what you mean.

@tsangyoujun

4 small O-rings, without tightening too much, do not crush them.

1 Like

Hi all ! …

To go on with my tunning mods for my VIM2+VTV+TONE in DIY-Case, here, inspired by fred21 cooling system mod…

Here I placed a sticky aluminuim foil to make a long lenght exhaust.
Fresh air is pulled by the fan and blowed through the covered heat sink.


At the exit I’ve put a flexibe piece of plastic label I’ve found on a brass plumbing fitting.

Vertical part of this ramp is maintained by the Wifi antenna to the side of the DIY-Case, the curved part is maintained by the heat sink itself.

Once the Tone-board in place, we can see clearly that the edge of the air exhaust plastic ramp perfectly channels the air outside.

See ya soon for another mod ! :wink:

DerFu

6 Likes

I used some metalized tape too, but I worry about covering the fins completely. At least if the fan is set to other than always on… My thinking on this is the tape will resists passive heat transfer when the fan is not running.
I used the tape to force the fan air to engage the HS fins longer. I stopped about half way so some of the fins could work passively.
Mind you, it is just my theory, I have not proven it.:grin:

3 Likes

I thunk about that, but regardless of the setup of the fan,
if the ships temperature reaches the high level start set,
the fan will start and blows out the hot air trought the grooves.
It’ll do that more efficiency and so it’ll run less time than usual.

VIM2 is continuously running like that since two days in idle mode,
I think passive heat sink is doing the job because the fan don’t star more often.

I’ll be carefull about fan running/stop cycles when I’ll charge the VIM2 ships.

2 Likes

Hi All, …

Found this mornig while searching parts from old computers …
Totaly covered CPU heat sink, fan blowing sideway…



So I don’t really think covering the fins completely on the VIM heat sink is a problem …
The problem is only if the fan never start to blow !

For the moment, VIM2 still continuously running sine 4 days.
If I’ve got the time this weekend, I’ll test it charging the ships.

3 Likes

Passive cooling solution for the DIY Case!


View: YouTube Video

5 Likes