How I ruin my Khadas Tone board along with VIMs Board


#1

Today I was arranging one sample to my client, he asked me better to make along with the heatsink together with Khadas VIM1 Basic and Tone Board. He told me he has a kid at home, better to have a cover for Tone board if it can be. Let me think…
Finally do some testing and adjusting, some amazing happened! What a good looking assembling!

on Youtube

Material:

Steps:

  1. Make Heatsink on VIM board firstly.
    Cover the Square silicone sheet on the CPU+eMMC+DDR, the down line of silicone sheet shall be not below the edge of eMMC. Then make the heatsink bring into the hole of VIM boards. Then put the combination aside.

04%20Khadas%20Heatsink

  1. Make the Upper Frame with the Garnish and GPIOs Cover, Put this combination on aside.

05%20Upper%20Frame%20with%20Garnish

06%20Upper%20Frame%20with%20Garnish%20and%20GPIOs%20Cover

  1. Fix the Middle Frame with the Down Frame. Use the Screw NO.1 = 4 PCS
    Notice the aligning of TF card between Upper Frame and Middle Frame to get the right directions.
    Thumb the screw NO.1 to the appointed holds.

07%20Get%20fix%20of%20middle%20and%20down%20frame%202
07%20Get%20fix%20of%20middle%20and%20down%20frame%201

  1. Foot of the case: Thumb Screw NO. 4 = 4PCS and Screw NO.6 = 4 PCS.
    Screw NO.6 as the foot of the device.
    But notice the height between Screw NO. 4 and Middle Frame’s edge. do not tighten it. As at the last step will tighten all.

10%20foot%20of%20case

  1. Fix the Weight Iron with the case.
    This step please notice the direction of TF card slot and the logo Khadas of weight iron.
    Then use the screw NO.1 = 4 pcs ( Total 8 PCS ) to fix the weight iron along with Khadas DIY Case.
    put the VIM board with heatsink inside the case.

12%20put%20the%20vim%20board%20inside%20the%20case

  1. put the VIMs board with heatsink into the case, and then put the antenna at the place of case.

  1. Fix the screw NO.7 with the Screw NO. 4 we did on Step 4.

14

  1. Put Khadas Tone Board fix to the VIMs GPIO headers. And then thumb the screw NO. 6 on the Screw NO.7

15%20Tone%20board%E5%89%AF%E6%9C%AC

  1. Thumb the screw NO. 8 to the holes on Khadas Tone board.
    Then put the Upper Frame we done on step 2, use the screw NO.3 to final thumb with the case.
    Finsh the DIY of Khadas Tone Board long with the Khadas VIM boards.

17%20Tone%20board%201

More other pitures for refer!
17%20Tone%20board%203

17%20Tone%20board%202

17%20Tone%20board


#2

Nice post Willow. :slight_smile:


#3

Always good when plenty of Hardware bits on hand,

Like that Purple

Does that mean mine is upside down, or your purple people eater :sunglasses::grinning::grinning::grinning:


#4

Yes, the initial inspiration from your design :blush:
with Weight Iron, the device on hand feel much more everything…


#5

Thanks,
Some long threaded rod would do the trick then you could space it out with TV tuner and Tone board
all in one unit easy


#6

Have to say I like the purple one kinda like bling. Hmmm connectors 3 on one 2 on Robert’s think I got to try one of these tone boards.


#7

Yes the Purple add that bling :wink:

A little more tinkering and all 3 are living happily ever after

Some Brass Rod found on ebay was the solution


#8

very nice DIY design. haha, it is very long Brass thread rod screw you have done a hardwork on it. Thank you.